Autel Maxi US AC W12-H Installation Manual Download Page 1

Web: www.autelenergy.com

Thank you for purchasing this Autel MaxiCharger AC Wallbox Home. Our equipment is manufactured to a high standard and 
— when used according to these instructions and properly maintained — will provide years of trouble-free performance.

• This equipment should only be installed by a licensed 

electrician in accordance with all local codes and ordi-
nances.

• This equipment must be grounded through a permanent 

wiring system or an equipment-grounding conductor.

• Do not install or use this equipment near flammable, 

explosive, harsh, or combustible materials, chemicals or 
vapors.

• Children should be supervised when around this equip-

ment.

• Do not insert fingers or foreign objects into the electric 

vehicle connector.

• Do not use the equipment if the flexible power cord or EV 

cable is frayed, broken or otherwise damaged, or fails to 
operate.

• Do not use the equipment if the enclosure or the EV 

connector is frayed, broken or otherwise damaged, or 
fails to operate.

• Use 90 °C wire copper conductors only.

• Do not operate the equipment outside its operating tem-

perature range of -40 to 131 °F (-40 to 55 °C).

• Incorrect installation and testing of the equipment could 

potentially damage the vehicle's battery, components, 
and/or the equipment itself.

• Handle the equipment with care during transportation. 

Do not subject it to strong force or impact or pull, twist, 
tangle, drag or step on the equipment, to prevent 
damage to it or any components.

IMPORTANT: 

Before operating or maintaining this equipment, please read these instructions carefully, 

paying extra attention to the safety warnings and precautions. Failure to use this product properly may cause 
damage and/or personal injury and will void the product warranty.

WARNING

1. LED Indicators (from left to right)

MaxiCharger AC Wallbox Home

Product Overview

• 

Power LED

• 

Internet Connection LED

• 

Charging LED

• 

Bluetooth Connection LED

1

MaxiCharger AC Wallbox Home

(Separate Holster)

Maxi US AC W12-H

2. RFID LED

3. EV Charging Cable

4. Bottom AC Inlet Hole

Installation Guide

Summary of Contents for Maxi US AC W12-H














Reviews: