Aussie BUSHMAN 7710.8.641 Assembly And Use Manual Download Page 3

7.  

WARNING!  If your grill catches on fire:

• If the fire is in the grill portion and you can safely

reach the control knobs, then turn them off by turning
knobs clockwise. If you cannot safely reach the 
control knobs, call the fire department.

• If the fire involves one of the hoses, and you can

safely reach the propane cylinder valve, shut the
valve off by turning LP cylinder valve handle 
clockwise to a full stop.

• If the fire involves the cylinder, leave it alone, 

evacuate the area and call the fire department.

• If there is any type of fire that threatens either 

personal safety or endangers property, call the fire
department.

8. Check the Grease Cup for grease buildup. Remove

excess grease to avoid a grease fire in the pan. 

Never

use the grill without  Grease Cup in place.

9.  

WARNING!

If you notice grease or other hot material

dripping from the grill onto valve, hose, or regulator, turn
off gas supply immediately.  After the grill has cooled, 

determine the cause and correct it.  After cleaning the

valve, hose and regulator, perform a leak test before
continuing use.  See 

Before Using Your LP Gas Grill

section (page 16) of this manual for correct leak test 
procedures.

10. This installation must conform with local codes or, in the

absence of local codes, with either the National Fuel Gas
Code, ANSI Z223.1, or CAN/CGA-B149.2, Propane

Installation Code.

11. If an external electrical source is utilized, the outdoor

cooking appliance, when installed, must be electrically
grounded in accordance with local codes or, in the
absence of local codes, with the National Electrical
Codes, ANSI/NFPA 70, or the Canadian Electrical Code.
CSA C22.1.

12. Keep any electrical supply cord and the fuel supply hose

away from any heated surfaces. Electric cords should be
placed away from walkways to avoid a tripping hazard.

13. Combustible materials should never be within  

36 in. of the back or sides of your LP gas grill.   

14. 

WARNING! Always Store Lp Cylinders upright

and where temperatures do not exceed 125 degrees
Fahrenheit. Never store a spare or disconnected LP

cylinder under or near this LP gas grill. 

17. Check the LP gas grill for gas leaks and burner 

obstructions before each use.   

WARNING!  Do not use a flame to check for gas

leaks.  

See

Before Using Your LP Gas Grill

section of

this manual for correct leak test procedures.  A clogged

burner tube can lead to a fire beneath grill. 

18. 

DANGER!  If you see, smell, or hear the hiss of

escaping gas from the LP cylinder:

A. Get away from the cylinder.

B. Do not attempt to correct the problem yourself.
C. Call your local fire department.

19. 

WARNING! Do not operate an LP gas grill if you

have knowledge of or suspect a gas leak.

20. Always inspect the gas hose and regulator assembly

before each use.  Always turn the LP cylinder to the “Off”
position before inspecting parts. If the hose is cut,

damaged, or showing signs of excessive abrasion or

wear, do not use the LP gas grill. Contact the 
manufacturer, as the hose must be replaced with an
assembly specified by the manufacturer prior to further
use of the LP gas grill.

21. 

WARNING! 

Before lighting the LP gas grill, open

the hood to prevent an explosion from gas build-up. 

See Operation of Your LP Gas Grill section 

22. If burner does not light, turn off all gas control knobs.

Leave the grill hood open and wait five minutes
before attempting to light.

23. If burner goes out during operation, turn off all gas

control knobs.  Open the hood and wait five minutes
before attempting to light.

24. Exercise reasonable care when using this LP gas grill.

Never leave grill unattended during use or cleaning.

25. Never allow children to operate or play near an LP gas

grill.  Keep animals and bystanders out of the grill area.

26. Always turn off the LP gas cylinder at the cylinder valve

when not in use. Allow grill to cool before handling parts
or cleaning.

27. WARNING

Do not move an LP gas grill when in

use or hot.

28. 

WARNING!

Never touch hot surfaces. Use heat 

resistant gloves, long-handled tongs, or cooking mitts at
all times.  The grill will become very hot.  Open the hood
carefully when cooking to avoid burns from the hot air
and steam trapped inside.

29.  Use only the hose and regulator assembly 

that is supplied with your LP gas grill and/or 
specified by the manufacturer.

3

Summary of Contents for BUSHMAN 7710.8.641





























Reviews: