background image

· Never connect or disconnect LP gas cylinder or fittings 

while grill is in use or is hot.  

· When the LP gas cylinder is connected, the grill must 

be kept outside in a well-ventilated space. Turn off all 
of the grill control knobs and the LP cylinder valve 
when grill is not in use.

· Move gas hose as far away as possible from hot surfaces.
· Place dust cap on cylinder valve outlet whenever the     

cylinder is not in use.  Only install the type of dust cap     
on the cylinder valve outlet that is provided with the     
cylinder valve.  Other types of caps or plugs may result     
in leakage of propane.

How to Connect your LP gas cylinder (See STEP 22 of
Assembly Instructions for diagram)

1) Make sure all of the control knobs are turned to the 

“off” position and verify that the LP gas cylinder valve is 
closed by turning the handle on the LP gas cylinder   
valve clockwise until it stops.

2) Remove the protective cap from the LP cylinder gas  

nozzle.

3) Hold regulator in a straight line with LP cylinder gas 

nozzle so the connection does not cross thread.

4) Insert Regulator nipple into the LP cylinder nozzle opening.
5) Hand tighten coupling nut in a clockwise direction.  

Do not use tools.

6) Perform a Leak Test.  (See STEP 10 of Assembly

Instructions for Leak Test Instructions)  

How to Disconnect your LP gas cylinder

1) Turn all control knobs to the “off” position and turn the 

handle on the LP gas cylinder clockwise until it stops.

2) Turn coupling nut on regulator in a counter-clockwise 

direction until regulator is released from threaded LP 
cylinder gas nozzle.

3) Place the protective cap over LP cylinder gas nozzle.

BEFORE USING YOUR

LP GAS GRILL

·  Do not use an LP gas grill indoors, on recreational 

vehicles, or on a boat.

· This LP gas grill is for outdoor use only and should be 

placed on firm, level surface.  The grill should be setup in 
an open area with good ventilation, away from high traffic 
areas and combustible materials.  

· Combustible or flammable materials should never be 

used or stored within 36 inches of the back or sides of  
your LP gas grill.  

· Locate your LP gas grill at least 10 feet away from your 

house or any building.  Do not use the grill in a garage, 
breezeway, carport, porch, or under a surface that can 
catch fire. 

· Carefully read the Important Safeguards section

of  this manual (pages 2 through 4).  Make sure
you follow and understand all instructions and
warnings.  If  you have any questions regarding
these pages, call 1-800-251-7558 and ask for a
Customer Service Representative.

· This installation must conform with local codes or, in

the absence of local codes, with either the National
Fuel Gas Code, ANSI Z223.1, or CAN/CGA-B149.2,
Propane Installation Code.

· If an external electrical source is utilized, the outdoor

cooking appliance, when installed, must be
electrically grounded in accordance with local codes
or, in the absence of local codes, with the National
Electrical Codes, ANSI/NFPA 70, or the Canadian
Electrical Code, CSA C22.1.

· If any electric appliance or rotisserie is used with the

LP gas grill, do not allow cords to touch or be near hot 

surfaces.  Electric cords should be placed away from 
walkways to avoid a tripping hazard.

· Grill storage cover must be removed and placed at

least 36 inches from the LP gas grill while in use.  The
grill cover is made of a flammable material.  The grill
must be completely cooled before putting the cover
back on the grill.

· Never store a spare or disconnected LP gas cylinder

under or near this LP gas grill.

· Inspect the hose and regulator assembly before each

use. If the hose is cut or damaged or shows signs of
excessive abrasion or wear, do not use the LP gas
grill. Contact the manufacturer, as the hose must be
replaced with an assembly specified by the 
manufacturer prior to the further use of the LP gas
grill.

· Use only the hose and regulator assembly that is

supplied with your LP gas grill.

· Use of this LP gas grill other than for the intended

use, or alteration of the LP gas grill in any way may
not be safe and will void any warranty.

· LP gas is not natural gas.  The conversion or 

attempted use of natural gas in an LP unit is 
dangerous and will void your warranty.

· Never use an LP gas cylinder if it shows signs of:

dents, gouges, bulges, fire damage, corrosion, 
leakage, excessive rust, or other forms of visual
external damage; it may be hazardous and should be
checked by a Liquefied Petroleum  supplier.  Do not
use an LP cylinder with a damaged valve.

· Never use charcoal in your LP gas grill.  Do not use

aerosols or store flammable liquids or materials near
this gas grill.

Selecting a Location

Precautions

16

Summary of Contents for BUSHMAN 7710.8.641





























Reviews: