background image

Identifying the Remote Control Buttons 

Battery Installation 

Open the battery lid behind the remote control and insert the two AAA batteries (included). Be sure to observe 

correct polarity (+/-) when placing the batteries into the compartment.   

Note

Never mix old and new batteries as this may result in leakage or cracking, possibly causing injuries to users

Caution

: A risk of explosion can result if batteries are replaced with an incorrect type. Always dispose of used 

batteries in accordance with local regulations.

 

 

 

 

*For future use 

Note:

 The remote control has a range of about 20 feet (6 meters) at a left to right angle of about 60° off center. 

Always point the remote control directly at the tuner. The remote control unit may not work properly if the 

remote control sensor on the tuner is under direct sunlight or subjected to other strong lighting. In such 

cases, suppress or change the angle of the lighting on the tuner, or operate the remote control unit closer to 

the tuner. 

Button 

Description 

Power 

Turns tuner ON and OFF 

Numeric Buttons

 

For entering channel number or password 

Mute 

Press to toggle audio output on and off 

VOL+/VOL- 

Press + to increase or 

– to decrease audio volume 

CH

 

Λ

/CH

 

V

 

Press

 

to change channels up or down 

Last 

Press to return to previous channel viewed 

Menu

 

Press to view or clear the OSD (On-Screen Display) menu 

Source* 

Input source selection 

Info 

Press to display information about the current channel 

Exit 

Press to return to the previous menu page or exit On-Screen Menu 



 

Use to highlight a desired menu item on the screen 

OK

 

Press to select a highlighted menu item 

CC/CS 

Press to select CC (Closed Caption) and CS (Caption Service) feeds   

Aspect 

Press to toggle through predefined aspect ratio modes 

Page 

Change to next page on EPG (Electronic Program Guide) 

EPG 

Press to display Electronic Program Guide 

Play* 

PVR Play 

Stop* 

PVR Stop 

Pause* 

PVR Pause 

Prev* 

PVR Skip Previous 

Next* 

PVR Skip Next 

Fwd* 

PVR Scan Forward 

Rev* 

PVR Scan Reverse 

Rec* 

PVR Record 

Summary of Contents for V-Tune Pro VPH-100



























Reviews: