background image

SAFETY INSTRUCTIONS 

Please review the following safety precautions. If this is the first time using this model of terrestrial TV 
tuner, then read this manual before installing or using the  tuner. If the tuner is not functioning properly, 
please contact your local distributor or system installer. 

 

 

The  lightning  symbol  in  the  triangle  is  used  to  alert  you  to  the  presence  of  dangerous  voltage 
inside the tuner that may be sufficient to constitute a risk of electric shock to anyone opening the 
case. It is also used to indicate improper installation or handling of the tuner that could damage 
the electrical system in the tuner or in other equipment attached to the tuner.

 

 

The exclamation point in the triangle is used to alert you to important operating and maintenance 
instructions.  Failure  to  follow  these  instructions  could  result  in  injury  to  you  or  damage  to  the 
tuner. 

   

Be careful with electricity:

 

 

Power outlet

:  To  prevent electric  shock,  be  sure  the electrical  plug  used on the  tuner

’s power cord matches 

the electrical outlet used to supply power to the tuner.   

 

Power cord

: Be sure the power cord is routed so that it will not be stepped on or pinched by heavy items. 

 

Power  overloading

:  Avoid  overloading  electrical  outlets  or  extension  cords  which  otherwise  could  result  in 

electric shock or fire. 

 

Lightning

:  For  protection  from  lightning  or  when  the  tuner  is  left  unattended  for  a  long  period,  disconnect  it 

from the power source. 

 

Protect  other  equipment

:  Unplug  the  tuner  before  connecting  any  other  equipment,  especially  the  TV 

antenna. Connect all equipment to the tuner before plugging in any power cords to the power source. 

 

Power line

: Be sure your TV antenna is not located near overhead power lines, or where it might fall into any 

power lines. Also be careful to avoid touching any such power lines when installing the TV antenna.   

 

Antenna Grounding

: Be sure that the antenna is grounded to provide protection from lightning and build-up of 

static electricity. Also, be sure that the power has been turned off before connecting any of the RF connectors. 

 

Also follow these precautions: 

 

Ventilation

: Do not block the ventilation slots on the tuner or place any heavy object on top of it. 

Blocking the air flow could damage the tuner. Arrange components so that air can flow freely around the tuner. 
Ensure that there is adequate ventilation if the tuner is placed in a stand. Put the tuner in a properly ventilated 
area, away from direct sunlight or any source of heat. 

 

Overheating

: Avoid stacking the tuner on top of a hot component such as a power amplifier. 

 

Risk of Fire

: Do not place the tuner on top of any easily combustible material, such as carpet or fabric. 

 

Proper  Connections

:  Be  sure  all  cables  and  equipment  are  connected  to  the  tuner  as  described  in  this 

manual. 

 

Object Entry

: To avoid electric shock, never stick anything in the slots on the case or remove the cover. 

 

Water Exposure

: To reduce the risk of fire or electric shock, do not expose the tuner to rain or moisture. 

 

Keep the tuner out of the reach of children or it may fall, causing injury or damage to the tuner. 

 

Always disconnect the power cord from the power outlet when you are not using the tuner.  This reduces your 
risk of electric shocks or fire. 

 

Always turn off the tuner, disconnect it from the power outlet, and unplug all other cables from before moving 
the tuner. This reduces your risk of electric shocks or fire. 

 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1)  This device may not cause harmful interference. 
(2)  This  device  must  accept  any  interferences  received,  including  interference  that  may  cause  undesired 

operation. 

 

"HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered 

trademarks of HDMI Licensing LLC."

 

 



 

EMI (Electro Magnetic Interference) tested 

 

Manuf

actured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of 

Dolby Laboratories.

 

 

 

WARNING! 

 

RISK OF ELECTRICAL SHOCK 

DO NOT OPEN 

WARNING: 

TO REDUCE THE RISK OF ELECTRICAL SHOCK 

DO NOT REMOVE THE COVER 

NO USER-SERVICEABLE PARTS ARE INSIDE 

REFER SERVICING TO QUALIFIED PERSONNEL

 

Summary of Contents for V-Tune Pro VPH-100



























Reviews: