background image

34

Special situations

ź

When 3 consecutive transmissions (after 15 minutes) from the 

AURATON 

3021R

 regulator are lost, an error is signalled on the RTH receiver (LED 

flashing continuously red and green). The RTH receiver starts executing the 
ON - OFF cycle memorised during the last 24 hours of operation until the 
problem is removed.

ź

When signal return (from the AURATON 3021R   regulator), the error is 

cancelled and the receiver enters its normal mode of operation.

ź

Switching  the  relay  is  synchronised  with  the  wave  of  the  230  V  mains 

voltage in order to ensure that closing and opening contacts of the relay 
occurs around the zero-crossing point. This prevents the occurrence of an 
electric arc, significantly extending the relay service time.

ź

The  RTH receiver is equipped with a unique algorithm for analysing the ON 

- OFF cycles. The entire heating cycle from the last 24 hours is recorded in 
the memory of the RTH receiver. In the event of losing communication with 
the AURATON 3021R regulator, the RTH receiver automatically executes 
the ON - OFF cycle memorised during the last 24 hours. This provides time 
for  restoring  transmission  (removing  interferences)  or  fixing  the  3021R 
regulator without a significant deterioration of thermal comfort conditions 
in the controlled spaces.

Unique features of AURATON 3021 RTH

35

Additional information and notes

ź

The AURATON 3021R regulatormust be installed at least 1 metre from the 

RTH  receiver  (too  strong  a  signal  from  the  transmitters  can  cause 
interference).

ź

At least 30 seconds must elapse between switching the relay off and on.

ź

Data  transmission  from  the  AURATON  3021R  regulator  to  the  receiver 

occurs upon each change of 0.2 °C of the surrounding temperature. When 
the  temperature  is  stable,  the  regulator  sends  heart-beat  data  every  5 
minutes  (which  is  signalled  with  the  LED  blinking  orange  on  the  RTH 
receiver).

ź

In the event of a power outage, the RTH receiver will switch off. When power 

is restored, the heating device is switched on automatically, and the RTH 
receiver awaits a signal from the paired transmitters (this signal should be 
received within 5 minutes of restoring power). After receiving the signal, the 
RTH receiver enters the normal mode of operation.

ź

The RTH receiver cannot be placed in metal containers (e.g. an assembly 

box,  a  metal  enclosure  of  a  heater)  in  order  to  not  to  interfere  with  its 
operation. 

ź

Pressing any function key for the first time always starts the backlight first, 

and then the key function is performed.

ź

While programming any function, if no key is pressed for 10 seconds, this will 

be interpreted as pressing the 

 key.

ź

The  control  functions  of  the  controller  can  be  switched  on  and  off 

(e.g. after heating season) by holding the 

key pressed for a while.

 

(The controller will display only the current time and temperature 
of the room - 

no "timeline”

 

)

.

[OK]

<ok. 

Summary of Contents for 3021













































Reviews: