manualshive.com logo in svg

AudioCodes 420HD, Administrator'S Manual, Page: 44 / 146

Share
Download
AudioCodes 420HD Administrator'S Manual Download Page 44

 

400HD Series IP Phone with Microsoft Lync 

Administrator's Manual 

44 

Document #: LTRT-09936 

Parameter

 

Description 

ƒ

 

[Australia] Australia 

ƒ

 

[USA] USA 

ƒ

 

[India] India 

[voip/regional_settings/use_config_file_values] 

Enables the user-defined CPT. When this parameter is 
enabled, the ‘selected_country’ parameter is not 
relevant and the CPT values below can be determined 
by the user. 

ƒ

 

[0] - Disable (default) 

ƒ

 

[1] - Enable 

Call Progress Tones (CPT) 

Note: Up to 10 CPTs can be configured (voip/regional_settings/call_progress_tones/0…9). 

[voip/regional_settings/call_progress_tones/%
d/enabled] 

Enables the specific CPT. 

ƒ

 

[0] - Disable 

ƒ

 

[1] - Enable 

[voip/regional_settings/call_progress_tones/%
d/name] 

Defines the name of the CPT. 

[voip/regional_settings/call_progress_tones/%
d/cadence] 

ƒ

 

Defines the cadence type of the tone.

 

ƒ

 

[0] - Continuous signal 

 

ƒ

 

[1] - Cadence signal 

 

ƒ

 

[2] - Burst signal  

[voip/regional_settings/call_progress_tones/%
d/frequency_a] 

Defines the low frequency (in Hz) of the tone. 

Range: 300 - 1980 Hz, in steps of 1 Hz.  
Unused frequencies must be set to zero. 

[voip/regional_settings/call_progress_tones/%
d/frequency_b] 

Defines the high frequency (in Hz) of the tone. 

Range: 300 - 3000 Hz, in steps of 1 Hz.  
Unused frequencies must be set to zero. 

[voip/regional_settings/call_progress_tones/%
d/frequency_a_level] 

Output level of the low frequency tone (in -dBm) in Call 
Progress generation. Range: 0 - 63, where 63 is mute. 

[voip/regional_settings/call_progress_tones/%
d/frequency_b_level] 

Output level of the low frequency tone (in -dBm) in Call 
Progress generation. Range: 0 - 63, where 63 is mute. 

[voip/regional_settings/call_progress_tones/%
d/tone_on_0] 

tone_on_0 to tone_on_3. 

If the signal is Cadence or Burst, then this value 
represents the on duration. If a Continuous tone, then 
this value represents the minimum detection time. In 
units of 10 msec. Range: 0 - 10000. 

[voip/regional_settings/call_progress_tones/%
d/tone_off_0] 

tone_off_0 to tone_on_3. 

If the signal is Cadence, then this value represents the 
off duration, in units of 10 msec. If not used, then set it 
to zero. If the signal is Burst, only tone_off 0 is relevant. 
It represents the off time that is required from the end of 
the signal to the detection time. Range: 0 - 10000. 

http://arttel.ru

http://arttel.ru/shop/ip-telefony/ip-telefon-audiocodes-420hd

Summary of Contents for 420HD



















































































































































Reviews:

No comments