background image

- 10 -

A10-RACK User Guide

For further information, contact Audio Ltd or your local distributor 

Copyright © 2018 Audio Ltd. All rights reserved. | 

www.audioltd.com

 

7 Century Court, Tolpits Lane, Watford WD18 9RS, UK | 

[email protected]

Legal Notices

FCC Notice

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 

conditions:

(1) This device may not cause harmful interference, and  

(2) This device must accept any interference received, including interference that may cause 

undesired operation.

FCC Part 15.19(a)(3)

Industry Canada Notice

This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the 

following two conditions:

(1) This device may not cause harmful interference, and  

(2) This device must accept any interference received, including interference that may cause 

undesired operation.

Declarations of Conformity

Hereby, Audio Ltd declares that the radio equipment type A10-RACK is in compliance with Low 

Voltage Directive 2014/35/EU, EMC Directive 2014/30/EU, and RoHS Directive 2011/65/EU.
The full text of the EU Declaration of Conformity and full text of the Supplier Declaration of 

Conformity for US are available at the following internet address: 

www.audioltd.com/DoC

WEEE Statement

If you have purchased a Sound Devices/Audio Ltd product in the EU and are intending 

to discard these products at the end of their useful life, please do not dispose of them 

with your other household or municipal waste. Sound Devices/Audio Ltd has labelled 

its branded electronic products with the WEEE Symbol to alert our customers that 

products bearing this label should not be disposed of in a landfill or with municipal or 

household waste in the EU.

Summary of Contents for A10-RACK











Reviews: