Atra Ace WOJ-3200 Instruction Manual Download

Page: 1 / 22

PORTABLE MAGNETIC DRILLING MACHINE

Read this manual carefully before operating your Nitto Kohki

Portable Magnetic Drilling Machine. Keep this manual with

your machine. All users of the Nitto Kohki Portable Magnetic

Drilling Machine must read this manual.

ATRA ACE

Model WOJ-3200

Professional Tool

For One-Touch Type Annular Cutter Only

(Side-Lock Type Annular Cutter cannot be used.)

Specifications

Model

WOJ-3200

Power Supply (Single Phase)

220-240 V

～

50/60 Hz

Drill Motor

Rated Power Consumption

950 W

Rated Current

4.3 A

No-load Speed

870 min

-1

Load Speed

550 min

-1

Magnet Power Consumption

70 W

Hole Capacity

JETBROACH One-touch Type Hole diameter MAX.

32 mm

Plate thickness MAX. 50 mm

Twist Drill

MAX. 13 mm

Magnet Holding Power

9000 N

Magnet Size

99 mm × 177 mm

Weight

13 kg

Short - Circuit Current Rating

5kA

The specifications and configurations contained in this document are subject to

change without prior notice due to improvements we are making day in, day out.

Manufactured by :

NITTO KOHKI Co., Ltd.

2-9-4, Nakaikegami, Ohta-ku,

Tokyo, 146-8555, Japan

TEL : (81)-3-3755-1111

FAX : (81)-3-3753-8791

E-mail : [email protected]

URL : www.nitto-kohki.co.jp

Keep the manual handy – so you can use it whenever necessary.

Original Instructions

WOJ-3200.indd 1

10.11.12 11:10:23 PM

Summary of Contents for WOJ-3200























Search results

Summary of Contents for WOJ-3200

Reviews:

Related manuals for WOJ-3200

Brands by name

Popular brands

Atra Ace WOJ-3200, Instruction Manual

Search results

Summary of Contents for WOJ-3200

Reviews:

Related manuals for WOJ-3200

Brands by name

Popular brands