background image

Atmos EasySolar Installation Instructions Evacuated Tube Collector 

10 

4.6 

Protection of plastic pipe and pipe insulation 

The red and blue collector pipes are made of plastic. It can occur that plastic pipes or 
pipe insulation material is damaged by rodents such as mice, rats or squirrels. Take 
appropriate precautions to protect the pipes and insulation material from this kind of 
attack if considered necessary.  
 

4.7 

Vented hot water systems 

The Atmos EasySolar system can be used as a preheat tank with a vented hot water 
system. The base of the cold water feed tank must be at least 1m above the base of the 
EasySolar tank, and the cold feed to the hot water cylinder passes through the cold/hot 
connections of the EasySolar tank. In most cases where the cold tank is in the roof 
space, a platform will be required of strong construction in accordance with the current 
standards.  
 

4.8 

Unvented hot water systems 

The Atmos EasySolar system can be used to provide preheated water to an unvented 
hot water cylinder. However the pressure reducing valve assembly as fitted on the cold 
water inlet feed of an unvented cylinder must be fitted 

before

 the EasySolar tank, and 

then the warm outlet from the EasySolar tank is connected to the cold inlet on the hot 
water cylinder (see page 12) 
 

4.9 

Connection to combi boiler 

The Atmos EasySolar hot water system can be used provide preheated water to a combi 
boiler. However the following points must be noted; 

a)  If the boiler is solar compatible (eg Atmos HE32 InterCombi) it can be connected 

directly to the cold water inlet as per the diagram on page 11. 

b)  If the boiler is not solar compatible, but can accept cold water at 28 deg C, a 

Combisol valve must be fitted (available from Atmos) 

c)  In all cases for combi boilers which are not solar compatible, the installer should 

check with the manufacturers that the boiler is able to accept cold water at 28 deg C 
inlet. If this is not acceptable, then an EasySolar system should not be fitted, or the 
boiler should be changed to a solar compatible type.  

Summary of Contents for EasySolar 15TC F 3M































Reviews: