Atmel AVR AT90S8515 Manual Download | Manualshive

Page: 50 / 101

background image

AT90S4414/8515

50

•

Bit 5 - UDRIE: UART Data Register Empty Interrupt Enable

When this bit is set (one), a setting of the UDRE bit in USR will cause the UART Data Register Empty interrupt routine to be
executed provided that global interrupts are enabled.
•

Bit 4 - RXEN: Receiver Enable

This bit enables the UART receiver when set (one). When the receiver is disabled, the TXC, OR and FE status flags cannot
become set. If these flags are set, turning off RXEN does not cause them to be cleared.
•

Bit 3 - TXEN: Transmitter Enable

This bit enables the UART transmitter when set (one). When disabling the transmitter while transmitting a character, the
transmitter is not disabled before the character in the shift register plus any following character in UDR has been
completely transmitted.
•

Bit 2 - CHR9: 9-bit Characters

When this bit is set (one) transmitted and received characters are 9 bit long plus start and stop bits. The 9th bit is read and
written by using the RXB8 and TXB8 bits in UCR, respectively. The 9th data bit can be used as an extra stop bit or a parity
bit.
•

Bit 1 - RXB8: Receive Data Bit 8

When CHR9 is set (one), RXB8 is the 9th data bit of the received character.
•

Bit 0 - TXB8: Transmit Data Bit 8

When CHR9 is set (one), TXB8 is the 9th data bit in the character to be transmitted.

BAUD Rate Generator

The baud rate generator is a frequency divider which generates baud-rates according to the following equation:

• BAUD = Baud-Rate

• fck= Crystal Clock frequency

• UBRR= Contents of the UART Baud Rate register, UBRR (0-255)

For standard crystal frequencies, the most commonly used baud rates can be generated by using the UBRR settings in
Table 18. UBRR values which yield an actual baud rate differing less than 2% from the target baud rate, are bolded in the
table. However, using baud rates that have more than 1% error is not recommended. High error ratings give less noise
immunity.

BAUD

f

CK

16(UBRR

1)

+

-------------------------------------

=

«
...
48
49
50
51
52
...
»

Summary of Contents for AVR AT90S8515






































































































Reviews:

No comments

Related manuals for AVR AT90S8515

Netlink FRX4000

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

H3C S7500E Series

Brand: H3C Pages: 34

SR8800 IM-FW-II

Brand: H3C Pages: 5

H3C S7500E Series

Brand: H3C Pages: 50

Brand: Commell Pages: 36

Brand: Roland Pages: 12

SteelCentral NetExpress

Brand: Riverbed Pages: 38

Brand: Altera Pages: 42

PARTNER PC CARD

Brand: Avaya Pages: 4

DIRECTOR PRO series

Brand: MF DIGITAL Pages: 79

Brand: addlink Pages: 9

1394 Dual-Port CardBus

Brand: SIIG Pages: 8

Brand: Technics Pages: 20

Brand: IEI Technology Pages: 2

Brand: Xantech Pages: 5

ipRocketLink IAD 3086

Brand: Patton electronics Pages: 12

Brand: Magewell Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands