Atmel AT90S2343 Manual Download Page 1

Page: 1 / 64

Features

•

Utilizes the AVR

RISC Architecture

•

AVR – High-performance and Low-power RISC Architecture

– 118 Powerful Instructions – Most Single Clock Cycle Execution
– 32 x 8 General-purpose Working Registers
– Up to 10 MIPS Throughput at 10 MHz

•

Data and Nonvolatile Program Memory

– 2K Bytes of In-System Programmable Flash

Endurance: 1,000 Write/Erase Cycles

– 128 Bytes Internal RAM
– 128 Bytes of In-System Programmable EEPROM

Endurance: 100,000 Write/Erase Cycles

– Programming Lock for Flash Program and EEPROM Data Security

•

Peripheral Features

– One 8-bit Timer/Counter with Separate Prescaler
– Programmable Watchdog Timer with On-chip Oscillator
– SPI Serial Interface for In-System Programming

•

Special Microcontroller Features

– Low-power Idle and Power-down Modes
– External and Internal Interrupt Sources
– Power-on Reset Circuit
– Selectable On-chip RC Oscillator

•

Specifications

– Low-power, High-speed CMOS Process Technology
– Fully Static Operation

•

Power Consumption at 4 MHz, 3V, 25

– Active: 2.4 mA
– Idle Mode: 0.5 mA
– Power-down Mode: <1 µA

•

I/O and Packages

– Three Programmable I/O Lines for AT90S/LS2323
– Five Programmable I/O Lines for AT90S/LS2343
– 8-pin PDIP and SOIC

•

Operating Voltages

– 4.0 - 6.0V for AT90S2323/AT90S2343
– 2.7 - 6.0V for AT90LS2323/AT90LS2343

•

Speed Grades

– 0 - 10 MHz for AT90S2323/AT90S2343-10
– 0 - 4 MHz for AT90LS2323/AT90LS2343-4
– 0 - 1 MHz for AT90LS2343-1

Pin Configuration

PDIP/SOIC

RESET

XTAL1

XTAL2

GND

VCC

PB2 (SCK/T0)

PB1 (MISO/INT0)

PB0 (MOSI)

AT90S/LS2323

RESET

(CLOCK) PB3

PB4

GND

VCC

PB2 (SCK/T0)

PB1 (MISO/INT0)

PB0 (MOSI)

AT90S/LS2343

8-bit

Microcontroller
with 2K Bytes of
In-System
Programmable
Flash

AT90S2323
AT90LS2323
AT90S2343
AT90LS2343

Rev. 1004D–09/01

Summary of Contents for AT90S2343

































































Search results

Summary of Contents for AT90S2343

Reviews:

Related manuals for AT90S2343

Brands by name

Popular brands

Atmel AT90S2343, Manual

Search results

Summary of Contents for AT90S2343

Reviews:

Related manuals for AT90S2343

Brands by name

Popular brands