Atlona AT-UHD-SW-5000ED, User Manual, Page: 18 / 25

18
atlona.com
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Commands
(TCP/IP and RS-232)
The command codes are case sensitive, do not change capitalization, spacing, or lettering.
Command Feedback Description
PWON PWON Turns switcher on
PWOFF PWOFF Turns switcher off
PWSTA PWSTA Displays power status
VersionX
e.g. Version OSD
VersionX
e.g. Version x.x.xx
Displays the software versions: ex. VersionMCU
firmware [MCU]
OSD menu [OSD]
DSP [DSP]
FPGA [FPGA]
Type AT-UHD-SW-5000ED Displays the model information
Mreset Mreset Reset device to manufacture default
Lock Lock Locks the front panel buttons
Unlock Unlock Unlocks the front panel buttons
x3AVx1 x3AVx1 Switch inputs Ex. Switch output 1 to input 4= x4AVx1
Status x2AVx1, x3AVx2 Displays what input is connected to the what output
x1$ X x1$ on Turns on/off output channel (X= on, off, sta)
e.g. x2$ off - Turns output 2 off
AutoSW X AutoSW on Turns auto switching on/off (X= on, off, sta)
IRON IRON Turns on the IR receiver window
IROFF IROFF Turns off the IR receiver window
EDIDCopyX memY
e.g.
EDIDCopy1 mem2
EDIDCopyX memY
e.g.
EDIDCopy1 mem2
Save the EDID of output X (1 or 2) to memory Y (1-8)
e.g.
Copy EDID of output 2 to memory 5 = EDIDCopy2 mem5
EDIDMSetX default EDIDMSetX default Set the EDID of the input to the default EDID
EDIDMSetX saveY EDIDMSetX saveY Set the EDID of an input to the previously saved EDID memory
e.g.
EDIDMset3 save1 - sets input 3 to EDID memory 1
EDIDMSetX intY EDIDMSetX intY Sets the EDID of an input to one of the internal EDIDs
e.g.
EDIDMSet2 int3 - Sets input 3 to internal EDID 3
HDCPSetX Y
e.g.
HDCPSet1 on
HDCPSetX Y
e.g.
HDCPSet1 on
Set HDCP reporting mode of the HDMI input (X= 1-5)(Y= on, off, sta)
e.g.
Input 3 to report HDCP non-compliant = HDCPSet3 off
AudioOutX Y AudioOutX on Turns the HDMI audio of each output (X= 1, 2) on/off (Y= on, off, sta)
e.g. Turn Output 2 HDMI audio off = AudioOut2 off
VOUT1 + VOUT1 XX Increases volume output by 1
VOUT1 - VOUT1 XX Decreases volume output by 1
VOUT1 YY
e.g.
VOUT1 -60
VOUT1 XX
e.g.
VOUT1 -60
Set volume output to a specific value (XX= -80 to 6)
VOUT1 sta VOUT1 YY Displays current volume output
VOUTMute1 X VOUTMute1 X Mute or unmute the output volume (X= on, off, sta)
Each command or feedback is terminated with a carriage return.
Note: If the command fails or is incorrect the feedback is “Command FAILED”
Note: Preferred timings include audio EDIDs as well. 2Ch is two channel audio, MCh is multi-channel audio
(including up to Dolby TrueHD or DTS-HD Master Audio), DD is Dolby Digital, and DVI does not include audio.
[Y] preferred timing -
STD
Sink
(pass through)
1 1080P 2Ch 2 1080P MCh
3
1080P DD
4
1080P 3D 2Ch
5
1080P 3D MCh
6 1080P 3D DD 7 720P 2CH 8 720P DD
9
1280x800 2Ch
10
1366x768 2Ch
11
1080P DVI
12 1280x800 DVI 13 3840x2160 2Ch 14 3840x2160 MCh