manualshive.com logo in svg

Atlas Copco GA 11 VSD, Instruction Book

Share
Download
Atlas Copco GA 11 VSD Instruction Book Download Page 76

9

Technical data

9.1

Readings on display

Display of Elektronikon regulator

Elektronikon II regulator

Important

The readings mentioned below are valid under the reference conditions (see section

Reference conditions and limitations

).

Reference

Reading

Air outlet pressure

Depends on the setpoint (desired net pressure).

Compressor element
outlet temperature

Approx. 65 ˚C (117 ˚F) above ambient temperature.

9.2

Electric cable size

Attention

• The voltage on the compressor terminals must not deviate more than 10% of the

nominal voltage.
It is however highly recommended to keep the voltage drop over the supply cables at
nominal current below 5% of the nominal voltage (IEC 60204-1). If cables are grouped
together with other power cables, it may be necessary to use cables of a larger size
than those calculated for the standard operating conditions.

• Use the original cable entry. See section 

Dimension drawings

.

To preserve the protection degree of the electric cubicle and to protect its components
from dust from the environment, it is mandatory to use a proper cable gland when
connecting the supply cable to the compressor.

• Local regulations remain applicable if they are stricter than the values proposed

below.

Instruction book

74

API161475

Summary of Contents for GA 11 VSD





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands