manualshive.com logo in svg

Atlas Copco GA 11 VSD, Instruction Book

Share
Download
Atlas Copco GA 11 VSD Instruction Book Download Page 77

CSA/UL versions

For 

UL

 designed machines, calculations for 

cable sections and fuses

 are done according to

UL508A (Industrial control panels).

For 

CSA

, calculations for 

cable sections and fuses

 are done according to CSA22.2 (Canadian

electrical code).

Standard conditions:

 maximum 3 copper conductors in raceway or cable with 85-90˚C (185-194

˚F) insulation at ambient temperature 30 ˚C (86 ˚F), operating at nominal voltage; cables not
grouped with other cables.

Worst case conditions:

 ambient temperature > 30 ˚C (86 ˚F), max. 3 copper conductors in

raceway or cable with 85-90 ˚C (185-194 ˚F) insulation at 46 ˚C (115 ˚F) ambient temperature
and operating at nominal voltage. Cables not grouped with other cables.

Fuse size is the max. fuse size in order to protect the motor against short circuit. For CSA fuse
HRC form II, for UL fuse class RK5.

If the local conditions are more severe then the described standard conditions, the cables and
fuses for worst case conditions should be used.

Cable size

Cable size

Frequency
(Hz)

Voltage
(V)

Cable size
GA 11 VSD

CSA/UL

 

AWG

60

460

AWG 6

9.3

Settings for fuses

Settings for fuses

GA 11 VSD

Frequency
(Hz)

Voltage
(V)

Fuses
(A)

CSA/UL

CSA HRC Form II/UL
Class 5

60

460

36

Instruction book

API161475

75

Summary of Contents for GA 11 VSD





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands