Atlantic WOYG LCT Series Maintenance Document Download Page 20

Page: 20 / 58

Clear 22: Discharge temperature protection (permanent stoppage)

LED

Hydraulic Unit

Outdoor Unit

Green

Red

ÀDVKHV

ÀDVK

ÀDVKHV

Probable causes:

Valve is close.

EEV failure.

Gas leak, less.

Discharge Thermistor failure.

Outdoor Fan operation failure.

Outdoor Heat Exchanger clogged.

Check:

Clear 22:

1. Check if gas valve is open:

If it is not open, open it and check the
operation.

2. Check EEV and Strainer:

Are EEV and Strainer open?

If EEV or Strainer is defective, replace it.

Cooling mode

1. Check if liquid valve is open:

If it is not open, open it and check the
operation.

2. Check EEV and Strainer:

Are EEV and Strainer open?

If EEV or Strainer is defective, replace it.

Heating mode

3. Check if gas leak or less gas:

Measure gas pressure, if there is a leak, correct it.

If recharging refrigerant, make sure to perform vacuuming and recharge the specified amount.

4. Check Discharge Pipe Thermistor:

- Is it on the holder?
- Is there a cable pinched?

Check characteristics of thermistor (Refer to Clear 7), If defective, replace the thermistor

5. Check Outdoor Heat Exchanger:

- Is there any obstructing the air flow route?
- Is there any clogging of outdoor unit Heat Exchanger?

If clogged, clear the clog.

6. Check Outdoor Fan:

Check Outdoor Fan Motor. (Refer to Clear 18)

If the Fan Motor is failure, replace it.

Maintenance document "1546 - EN"

Outoor unit - excellia (duo)

WOYGxxxLCT_WOYKxxxLCT

- 20 -

Summary of Contents for WOYG LCT Series



























































Search results

Summary of Contents for WOYG LCT Series

Reviews:

Brands by name

Popular brands

Atlantic WOYG LCT Series, Maintenance Document

Search results

Summary of Contents for WOYG LCT Series

Reviews:

Brands by name

Popular brands