15
S
S
a
a
f
f
e
e
t
t
y
y
i
i
n
n
s
s
t
t
r
r
u
u
c
c
t
t
i
i
o
o
n
n
s
s
Observe the following advices in order to protect
yourself and other persons against possible injuries.
L
Pass the safety instructions on to all persons who
work with the machine.
L
Keep these safety instructions in a safe place.
Repair works on the device must be carried out by
the manufacturer or by companies appointed by
the manufacturer respectively.
Make yourself familiar with the equipment before using
it, by reading and understanding the operating
instructions.
Do not use the machine for unsuitable purposes (see
“Proper use”).
Be observant. Attend to what you do. Start working with
rationality. Do not use the device when you are tired or
under the influence of drugs, alcohol or medicaments.
One moment of carelessness when using the device
can result in serious injuries
.
Operate the saw dust extraction device only on
−
solid
−
even
−
vibration-free ground.
Sufficient fresh air and light conditions must be
provided.
Keep your workplace in an orderly condition! Untidiness
can result in accidents.
Do not operate the saw dust extraction device neither in
moist or wet surroundings nor near inflammable liquids
or gases.
Operating the extraction device is not permitted in
explosive rooms.
Not absorbed shall be:
−
spark producing machines or ignition sources.
−
wooden and metallic parts.
−
explosive and insanitary media as finish fog, gases
and dusts.
Only operate the machine with complete and correctly
attached safety equipment and do not alter anything on
the machine that could impair the safety.
Faulty or damaged parts in the device must be replaced
immediately.
Do not leave the machine standing in the rain or use
when raining.
Never leave the machine unattended.
The operation is prohibited for persons younger than 16
years and persons not familiar with the extraction
system.
Within his area of work the operator is responsible for
third parties.
Keep children away form machine.
Do not spray machine with water (this is hazardous due
to live components).
Keep the device in a safe place. Keep not used devices
in a dry, closed and for children inaccessible room.
Switch the machine off and remove the mains plug from
the socket when
−
carrying out repair works
−
maintenance and cleaning
−
removal of faults
−
checking of connection cables whether they are
swallowed or damaged
−
transport
−
Replacing the saw dust bag
−
Leaving the machine (also during temporary
interruption)
Check the machine for possible damage:
−
Before further use of the machine the protection
devices or slightly damaged parts must be checked
carefully for their proper and intended function.
−
Check whether the movable parts function perfectly
and do not stick or whether the parts are damaged,
All parts must be correctly installed and fulfil all
conditions to ensure perfect operation of the
machine.
−
Damaged protective devices and parts must be
repaired or replaced properly by an approved
specialised repair shop or the manufacturer, unless
otherwise indicated in the instruction manual.
−
Damaged or illegible security labels have to be
replaced.
Electrical safety
Design of the connection cable according to IEC 60
245 (H 07 RN-F) with a core cross-profile section of at
least
−
1.5 mm
2
for cable lengths up to 25 m
−
2.5 mm
2
for cable lengths over 25 m
Long and thin connection lines result in a potential drop.
The motor does not reach any longer its maximal
power; the function of the device is reduced.
Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic
material of same mechanical stability or be covered with
this material.
The connector of the connection cable must be splash-
proof.
When running the connection line observe that it does
not interfere, is not squeezed, bended and the plug
connection does not get wet.
Do not use the cable for purposes for which it is not
meant. Protect the cable against heat, oil and sharp
edges. Do not use the cable to pull the plug from the
socket.
Wind off completely the cable when using a cable drum.
Regularly check the extension cables and replace them
if they are damaged.
Do not use any defective connection cables.
When working outdoors, only use extension cables
especially approved and appropriately labelled for
outdoor use.
Do not set up any provisional electrical connections.
