Atheros AP222A User Manual Download Page 55

Page: 55 / 81

COMPANY CONFIDENTIAL

dbgLVL

#iwpriv ath

Yet another debug control. This parameter controls the debug level of the VAP based debug print statements.
It’s normally set to zero, eliminating all prints.

Table 11 802.11 Protocol Layer Debug Bitmask

Symbolic Name

Bit Value

Description

IEEE80211_MSG_11N

0x80000000

11n mode debug

IEEE80211_MSG_DEBUG

0x40000000

IFF_DEBUG equivalent

IEEE80211_MSG_DUMPPKTS

0x20000000

IFF_LINK2 equivalent

IEEE80211_MSG_CRYPTO

0x10000000

crypto work

IEEE80211_MSG_INPUT

0x08000000

input handling

IEEE80211_MSG_XRATE

0x04000000

rate set handling

IEEE80211_MSG_ELEMID

0x02000000

element id parsing

IEEE80211_MSG_NODE

0x01000000

node handling

IEEE80211_MSG_ASSOC

0x00800000

association handling

IEEE80211_MSG_AUTH

0x00400000

authentication handling

IEEE80211_MSG_SCAN

0x00200000

Scanning

IEEE80211_MSG_OUTPUT

0x00100000

output handling

IEEE80211_MSG_STATE

0x00080000

state machine

IEEE80211_MSG_POWER

0x00040000

power save handling

IEEE80211_MSG_DOT1X

0x00020000

802.1x authenticator

IEEE80211_MSG_DOT1XSM

0x00010000

802.1x state machine

IEEE80211_MSG_RADIUS

0x00008000

802.1x radius client

IEEE80211_MSG_RADDUMP

0x00004000

dump 802.1x radius packets

IEEE80211_MSG_RADKEYS

0x00002000

dump 802.1x keys

IEEE80211_MSG_WPA

0x00001000

WPA/RSN protocol

IEEE80211_MSG_ACL

0x00000800

ACL handling

IEEE80211_MSG_WME

0x00000400

WME protocol

IEEE80211_MSG_SUPG

0x00000200

SUPERG

IEEE80211_MSG_DOTH

0x00000100

11.h

IEEE80211_MSG_INACT

0x00000080

inactivity handling

IEEE80211_MSG_ROAM

0x00000040

sta-mode roaming

IEEE80211_MSG_ACTION

0x00000020

action management frames

Summary of Contents for AP222A


















































































Search results

Summary of Contents for AP222A

Reviews:

Brands by name

Popular brands

Atheros AP222A, User Manual

Search results

Summary of Contents for AP222A

Reviews:

Brands by name

Popular brands