manualshive.com logo in svg

ATC Labs Perceptual SoundMax Q24, Operation Manual, Page: 9 / 56

Share
Download
ATC Labs Perceptual SoundMax Q24 Operation Manual Download Page 9

 

 

 

 

 

 

 

A T C   L a b s   C o p y r i g h t   ( 2 0 1 2 )   A l l   R i g h t s   R e s e r v e d .  

 

Page 9 

 

 

 

   Input and Output Connections: 

1.

 

Baseband Input SCA – BNC Connector 

2.

 

Baseband Input RDS/RBDS– BNC Connector 

3.

 

Composite Baseband Output 1 (COMP/MPX) – BNC Connector 

4.

 

Composite Baseband Output 2  (COMP/MPX/PILOT)– BNC Connector 

5.

 

Balanced Analog Input  (Right) - XLR Connector 

6.

 

Balanced Analog Input  (Left) – XLR Connector 

7.

 

Balanced Analog Out (Right) – XLR Connector 

8.

 

Balanced Analog Out (Left) – XLR Connector 

9.

 

AES/EBU Digital Input – XLR Connector 

10.

 

AES/EBU Digital Output  – XLR Connector 

11.

 

USB Connector 

12.

 

Ethernet Connector – RJ 45 

13.

 

3-bin Power Chord Connector (with earthing) 

14.

 

Master ON/OFF Switch 

 

 

 Connecting analog audio equipment: 

The left and right analog inputs are on EMI-

suppressed  XLR-type  female  connectors  on  the  rear  panel.  Input  impedance  is 

greater than 10k

Ω

; balanced and floating. Inputs can accommodate up to +24 dBu (0 

dBu = 0.775Vrms).  

The left and right analog outputs are on EMI-suppressed XLR-type male connectors 

on the rear panel. Output impedance is 50

Ω

; balanced and floating. They can drive 

600

Ω

  or  higher  impedances,  balanced  or  unbalanced.  The  peak  output  level  is 

adjustable from –6 dBu to +24 dBu. Level control of the analog inputs and outputs is 

accomplished via front-panel control through System Setup (Section 3.2.2). 

 

 

 Connecting digital audio equipment: 

The digital input and outputs conform to the 

professional  AES/EBU  standard.  They  all  have  sample  rate  converters  to  allow 

operation  at  32  kHz,  44.1  kHz,  48  kHz  sample  frequency.  On  the  input the  sample 

rate  is  auto  sensed.  For  best  peak  control,  operate  at  44.1  kHz  or  higher.  The 

left/right  digital  input  is  on  one  XLR-type  female  connector  on  the  rear  panel;  the 

Summary of Contents for Perceptual SoundMax Q24

























































Reviews:

No comments