ATC Labs Perceptual SoundMax Q24 Operation Manual Download Page 31 | Manualshive

Page: 31 / 56

ATC Labs Perceptual SoundMax Q24 Operation Manual Download Page 31

A T C L a b s C o p y r i g h t ( 2 0 1 2 ) A l l R i g h t s R e s e r v e d .

Page 31

4.1.2

Accurate Multiband Dynamic Range Compression (DRC):

Multiband Dynamic Compression improves the consistency of the FM

stations sound. It also remarkably increases the loudness of the program material,

without producing unpleasant side effects.

To change the dynamic range in different bands individually this module is

provided with greater functionality than any other product available on the market.

We use a specially designed filterbank for generating a time-frequency representation

of the signal that provides a very high level of control both in time and frequency

domain.

Moreover, the processing filterbank is completely linear-phase, eliminating

phase distortions and the need to compensate for phase distortions.

Internal processing is in 24 processing bands.

The number of bands that

are available for user control is flexible; user can configure dynamic range control

parameters in 2, 4, 6, 10, or 24 bands.

Figure 4.3: DRC Configuration Screen

The menu located just below the

DRC BANDS

tag is for bands selection.

Appropriate numbers of sliders are selected depending on the band selection e.g., For

TEN, SIX, FOUR, and TWO bands. If any slider is at bottom position then dynamic

range in that band is unchanged and if the slider is at top position then dynamic range

«
...
29
30
31
32
33
...
»

Summary of Contents for Perceptual SoundMax Q24

























































Reviews:

No comments