AT&T TL7600 User Manual Download Page 52 | Manualshive

Page: 52 / 61

background image

47

Appendix B

FCC Part 15

This  equipment  has  been  tested  and  found  to  comply  with  the
requirements  for  a  Class  B  digital  device  under  Part  15  of  the
Federal Communications Commission (FCC) rules.
These requirements are intended to provide reasonable protection
against  harmful  interference  in  a  residential  installation.  This
equipment  generates,  uses  and  can  radiate  radio  frequency
energy  and,  if  not  installed  and  used  in  accordance  with
the  instructions,  may  cause  harmful  interference  to  radio
communications. However, there is no guarantee that interference
will not occur in a particular installation.
If  this  equipment  does  cause  harmful  interference  to  radio  or
television  reception,  which  can  be  determined  by  turning  the
equipment  off  and  on,  the  user  is  encouraged  to  try  to  correct
the interference by one or more of the following measures:
•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect  the  equipment  into  an  outlet  on  a  circuit  different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

Changes  or  modifications  to  this  equipment  not  expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This  device  complies  with  Part  15  of  the  FCC  Rules.  Operation
is  subject  to  the  following  two  conditions:  (1)  this  device  may
not  cause  harmful  interference,  and  (2)  this  device  must  accept
any  interference  received,  including  interference  that  may  cause
undesired  operation.  Privacy  of  communications  may  not  be
ensured when using this device.

«
...
50
51
52
53
54
...
»

Summary of Contents for TL7600






























































Reviews:

No comments

Related manuals for TL7600

Brand: OCULUS Pages: 9

Brand: OCULUS Pages: 4

Brand: ACV Pages: 18

Brand: 2GO Pages: 12

Brand: Uniden Pages: 2

Brand: Uniden Pages: 2

Brand: Uniden Pages: 8

Brand: Uniden Pages: 2

Brand: Uniden Pages: 2

Brand: Uniden Pages: 16

Brand: Jabra Pages: 2

Brand: Jabra Pages: 11

Brand: Nacon Pages: 3

DELTACO DELO-0651

Brand: Nordic Pages: 16

Eye-Trek FMD-250W

Brand: Olympus Pages: 31

Brand: Jabra Pages: 28

Brand: WINTORY Pages: 10

Brand: Lucent Technologies Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands