Setting up integral and external
controls options
With the upgraded i-range of ATAG boilers, there may be some settings you need to change depending on what controls
you are using externally or in case you use the new integral programmer function.
If you are just connecting a control that is working with the volt free On/Off, OpenTherm or 230V SwL connection, then
there are no changes as this is the factory default set up. So, you can just plug in and play.
If you are using an ATAG ONE
Zone
, ATAG Cube or outside weather compensator, then you will need to change the
‘Thermoregulation setting’.
This can be done as follows:
RESET
BACK
OK
19°
25/07/18 09:00
80°
60°
ECO
AUTO
Press OK to enter Menu
1.5 bar
Insert Code
007
Save
Insert technical code
Technical area
Language, date and time
Complete Menu
Configuration Wizard
Service
Faults
Menu
0
1
2
3
4
Network
<Not Available>
Boiler Parameters
<Not Available>
Zone 1 Parameters
From the controller Home screen,
press the
BACK
and
OK
buttons
at the same time for 7 seconds
1
Turn the selector wheel to highlight
007
as the Technical Code. Press
OK
to Save.
2
The screen below appears.
This way you have access to the complete
parameter level.
4
Now select 4. Zone 1 Parameters
a.
Next select 4.2 Z1 Settings
b.
Next select 4.2.1 Thermoregulation.
Within this parameter of the boiler you can
select from 0 – 4. See the table below
5
The screen below then appears.
Turn the selector wheel to highlight
Complete Menu
. Press
OK
. It takes
a while to load the menu.
3
No.
Description
Volt Free Connector Colour
Controls
0
=
Fixed flow temperature (On/off or OpenTherm controller) (Factory setting) manual mode 0 = OFF 1 = ON
On / Off stat
OpenTherm
1
=
Do not use
-
-
2
=
Room control with ATAG ONE
Zone
controller (Room temp only / thermostat mode)
ATAG ONE
Zone
or Cube
3
=
Weather Compensation (Outside sensor only or with On/off or OpenTherm controller) (4.7.0 & 4.7.2)
Outside sensor with
On / Off stat or
OpenTherm
4
=
Weather dependent control - with Room compensation (Only for ATAG ONE
Zone
controllers)
(ATAG ONE
Zone
in weather dependent mode)
ATAG ONE
Zone
Terminal block LV iC-Range
ATAG Outdoor sensor 1kOhm*
n.a. = not applicable
ATAG Zone connection
OpenTherm or ON/OFF thermostat
n.a. = not applicable
DHW sensor T3
External safety contact
terminal block
PE
N
PE
L
N
L’
230V o
ut
230V Co
ntro
l
PE
N
L
230V in
N
L
230V o
ut
DO NOT CONNECT 230 VO
LT
* Mounting on north – north/east facade of the house. Prevent outside influences such as snow, ventilation air or chimney heat.
230V live output
to pump
E
N
L
E
L
N
SwL
230V out
230V Control
E
N
L
230V in
N
L
230V out
230V control terminal block iC-Range
N:
Neutral
L:
Live
E:
Earth
N:
Neutral
L:
Live
E:
Earth
L:
Live
N:
Neutral
SwL:
Switched live
230V live input only!
E:
Earth pump
N:
Neutral pump
L:
Live pump
230V live output
230V out
230V in LNE
Terminal block LV iC-Range
ATAG Outdoor sensor 1kOhm*
n.a. = not applicable
ATAG Zone connection
OpenTherm or ON/OFF thermostat
n.a. = not applicable
DHW sensor T3
External safety contact
terminal block
PE
N
PE
L
N
L’
230V o
ut
230V Co
ntro
l
PE
N
L
230V in
N
L
230V o
ut
DO NOT CONNECT 230 VO
LT
* Mounting on north – north/east facade of the house. Prevent outside influences such as snow, ventilation air or chimney heat.
230V live output
to pump
E
N
L
E
L
N
SwL
230V out
230V Control
E
N
L
230V in
N
L
230V out
230V control terminal block iC-Range
N:
Neutral
L:
Live
E:
Earth
N:
Neutral
L:
Live
E:
Earth
L:
Live
N:
Neutral
SwL:
Switched live
230V live input only!
E:
Earth pump
N:
Neutral pump
L:
Live pump
230V live output
230V out
230V in LNE
Terminal block LV iC-Range
ATAG Outdoor sensor 1kOhm*
n.a. = not applicable
ATAG Zone connection
OpenTherm or ON/OFF thermostat
n.a. = not applicable
DHW sensor T3
External safety contact
terminal block
PE
N
PE
L
N
L’
230V o
ut
230V Co
ntro
l
PE
N
L
230V in
N
L
230V o
ut
DO NOT CONNECT 230 VO
LT
* Mounting on north – north/east facade of the house. Prevent outside influences such as snow, ventilation air or chimney heat.
230V live output
to pump
E
N
L
E
L
N
SwL
230V out
230V Control
E
N
L
230V in
N
L
230V out
230V control terminal block iC-Range
N:
Neutral
L:
Live
E:
Earth
N:
Neutral
L:
Live
E:
Earth
L:
Live
N:
Neutral
SwL:
Switched live
230V live input only!
E:
Earth pump
N:
Neutral pump
L:
Live pump
230V live output
230V out
230V in LNE
Terminal block LV iC-Range
ATAG Outdoor sensor 1kOhm*
n.a. = not applicable
ATAG Zone connection
OpenTherm or ON/OFF thermostat
n.a. = not applicable
DHW sensor T3
External safety contact
terminal block
PE
N
PE
L
N
L’
230V o
ut
230V Co
ntro
l
PE
N
L
230V in
N
L
230V o
ut
DO NOT CONNECT 230 VO
LT
* Mounting on north – north/east facade of the house. Prevent outside influences such as snow, ventilation air or chimney heat.
230V live output
to pump
E
N
L
E
L
N
SwL
230V out
230V Control
E
N
L
230V in
N
L
230V out
230V control terminal block iC-Range
N:
Neutral
L:
Live
E:
Earth
N:
Neutral
L:
Live
E:
Earth
L:
Live
N:
Neutral
SwL:
Switched live
230V live input only!
E:
Earth pump
N:
Neutral pump
L:
Live pump
230V live output
230V out
230V in LNE
Terminal block LV iC-Range
ATAG Outdoor sensor 1kOhm*
n.a. = not applicable
ATAG Zone connection
OpenTherm or ON/OFF thermostat
n.a. = not applicable
DHW sensor T3
External safety contact
terminal block
PE
N
PE
L
N
L’
230V o
ut
230V Co
ntro
l
PE
N
L
230V in
N
L
230V o
ut
DO NOT CONNECT 230 VO
LT
* Mounting on north – north/east facade of the house. Prevent outside influences such as snow, ventilation air or chimney heat.
230V live output
to pump
E
N
L
E
L
N
SwL
230V out
230V Control
E
N
L
230V in
N
L
230V out
230V control terminal block iC-Range
N:
Neutral
L:
Live
E:
Earth
N:
Neutral
L:
Live
E:
Earth
L:
Live
N:
Neutral
SwL:
Switched live
230V live input only!
E:
Earth pump
N:
Neutral pump
L:
Live pump
230V live output
230V out
230V in LNE
32
