Asus CROSSHAIR IV EXTREME User Manual Download Page 66

Page: 66 / 172

2.8.4

ASUS Q-Connector (system panel)

Use the ASUS Q-Connector to connect/disconnect the chassis front panel cables.

To install the ASUS Q-Connector:
1. Connect the front panel cables to the

ASUS Q-Connector.

Refer to the labels on the

Q-Connector to know the detailed

pin definitions, and then match them

to their respective front panel cable

labels.

The labels on the front panel

cables may vary depending on the

chassis model.

2. Install the ASUS Q-Connector to the

system panel connector, ensuring

the orientation matches the labels

on the motherboard.

3. The front panel functions are now

enabled. The figure shows the Q-

Connector is properly installed on

the motherboard.

IDE_LED

POWER SW

RESET SW

IDE_LED-

PWR

Reset

Ground

2-40

Chapter 2: Hardware information

Summary of Contents for CROSSHAIR IV EXTREME













































































































































































Search results

Summary of Contents for CROSSHAIR IV EXTREME

Reviews:

Asus CROSSHAIR IV EXTREME, User Manual, Page: 66 / 172

Search results

Summary of Contents for CROSSHAIR IV EXTREME

Reviews: