manualshive.com logo in svg

Asus CROSSHAIR IV EXTREME, User Manual, Page: 151 / 172

Share
Download
Asus CROSSHAIR IV EXTREME User Manual Download Page 151

ROG Crosshair IV Formula

4-29

4.4.3 

Setting the RAID item in BIOS

You must enable the RAID function in the BIOS Setup before creating RAID 

volume(s) using SATA HDDs. To do this:

1.  Enter the BIOS Setup during POST.
2.  Go to the 

Main

 menu > Storage Configuration, and then press <Enter>.

3.  Set the 

OnChip SATA Channel

 item to [RAID].

4.  Save your changes, and then exit the BIOS Setup.

Refer to Chapter 3 for details on entering and navigating through the BIOS 

Setup.

When setting the 

OnChip SATA Channel

 item to [RAID], all SATA ports run at 

RAID mode. However, you can set the SATA ports 5 and 6 to [IDE] mode. See 

section 3.4.5 Storage Configuration for details.

4.4.2 

Installing Serial ATA hard disks

The motherboard supports Serial ATA hard disk drives. For optimal performance, 

install identical drives of the same model and capacity when creating a disk array.

To install the SATA hard disks for a RAID configuration:

1.  Install the SATA hard disks into the drive bays.
2.  Connect the SATA signal cables.
3.  Connect a SATA power cable to the power connector on each drive.

Summary of Contents for CROSSHAIR IV EXTREME













































































































































































Reviews:

No comments