Asus AAEON GENE-TGU6 User Manual Download

Page: 66 / 135

Chapter 3

–

AMI BIOS Setup

3.5

”

mp
act

ard

ENE

-T

3.2 AMI BIOS Setup

The AMI BIOS ROM has a pre-installed Setup program that allows users to modify basic

system configurations, which is stored in the battery-backed CMOS RAM and BIOS

NVRAM so that the information is retained when the power is turned off.

To enter BIOS Setup, press <Del> or <ESC> immediately while your computer is

powering up.

The function for each interface can be found below.

Main

–

Date and time can be set here. Press <Tab> to switch between date elements

Advanced

–

Access advanced hardware settings and Hardware Monitor

System I/O

–

Configure I/O settings including PCI Express and storage options

Security

–

Set admin and user passwords, access secure boot options

Boot

–

Boot options including BBS priority and Quiet Boot options

Save & Exit

–

Save your changes and exit the program

Summary of Contents for AAEON GENE-TGU6








































































































































Search results

Summary of Contents for AAEON GENE-TGU6

Reviews:

Related manuals for AAEON GENE-TGU6

Brands by name

Popular brands

Asus AAEON GENE-TGU6, User Manual

Search results

Summary of Contents for AAEON GENE-TGU6

Reviews:

Related manuals for AAEON GENE-TGU6

Brands by name

Popular brands