Asus AAEON BOXER-6839-CFL User Manual Download Page 59

Page: 59 / 138

Chapter 3

–

AMI BIOS Setup

Fan

les

s E

mb
ed

ded

BO
XE

R-

6839

-CFL

3.1 System Test and Initialization

The system uses certain routines to perform testing and initialization during the boot

up sequence. If an error, fatal or non-fatal, is encountered, the system will output a few

short beeps or an error message. The board can usually continue the boot up

sequence with non-fatal errors.

The system configuration verification routines check the current system configuration

against the values stored in the CMOS memory. If they do not match, an error message

will be output, and the BIOS setup program will need to be run to set the configuration

information in memory.

There are three situations in which the CMOS settings will need to be set or changed:

Starting the system for the first time

The system hardware has been changed

The CMOS memory has lost power and the configuration information is erased

The system

’

s CMOS memory uses a backup battery for data retention. The battery

must be replaced when it runs down.

Summary of Contents for AAEON BOXER-6839-CFL











































































































































Search results

Summary of Contents for AAEON BOXER-6839-CFL

Reviews:

Related manuals for AAEON BOXER-6839-CFL

Brands by name

Popular brands

Asus AAEON BOXER-6839-CFL, User Manual

Search results

Summary of Contents for AAEON BOXER-6839-CFL

Reviews:

Related manuals for AAEON BOXER-6839-CFL

Brands by name

Popular brands