Asus AAEON BOXER-6839-CFL User Manual Download Page 8

Page: 8 / 138

Preface

VIII

Fan

les

s E

mb
ed

ded

x PC

BO
XE

R-

6839

-CFL

FCC Statement

This device complies with Part 15 FCC Rules. Operation is

subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept

any interference received including interference that may

cause undesired operation.

Caution:

There is a danger of explosion if the battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer. Dispose of used batteries

according to the manufacturer’s instructions and your local government’s recycling or

disposal directives.

Attention:

Il y a un risque d’ex

plosion si la batterie est remplacée de façon incorrecte.

Ne la remplacer qu’avec le même modèle ou équivalent recommandé par le

constructeur. Recycler les batteries usées en accord avec les instructions du fabricant et
les directives gouvernementales de recyclage.

Summary of Contents for AAEON BOXER-6839-CFL











































































































































Search results

Summary of Contents for AAEON BOXER-6839-CFL

Reviews:

Related manuals for AAEON BOXER-6839-CFL

Brands by name

Popular brands

Asus AAEON BOXER-6839-CFL, User Manual

Search results

Summary of Contents for AAEON BOXER-6839-CFL

Reviews:

Related manuals for AAEON BOXER-6839-CFL

Brands by name

Popular brands