A S U S R S 1 2 0 - E 3 / P A 4
A S U S R S 1 2 0 - E 3 / P A 4
A S U S R S 1 2 0 - E 3 / P A 4
A S U S R S 1 2 0 - E 3 / P A 4
A S U S R S 1 2 0 - E 3 / P A 4
5 - 1 5
5 - 1 5
5 - 1 5
5 - 1 5
5 - 1 5
ATA/IDE Configuration [Enhanced]
ATA/IDE Configuration [Enhanced]
ATA/IDE Configuration [Enhanced]
ATA/IDE Configuration [Enhanced]
ATA/IDE Configuration [Enhanced]
Allows selection of the IDE operation mode depending on the installed operating
system (OS). Set to [Enhanced] mode if you are using native OS, e.g. Windows
®
Server 2000/2003. Set to [Compatible] mode if you are using legacy OS,
e.g. Windows ME/98/NT, MS-DOS. Configuration options: [Disabled]
[Compatible] [Enhanced]
5.3.4
5.3.4
5.3.4
5.3.4
5.3.4
IDE Configuration
IDE Configuration
IDE Configuration
IDE Configuration
IDE Configuration
The items in this menu allow you to set or change the configurations for the
IDE devices installed in the system. Select an item then press <Enter> if you
want to configure the item.
The Configure SATA As
Configure SATA As
Configure SATA As
Configure SATA As
Configure SATA As and Third IDE Master/Slave
Third IDE Master/Slave
Third IDE Master/Slave
Third IDE Master/Slave
Third IDE Master/Slave items appear
only when you set the ATA/IDE Configuration to [Enhanced] mode.
Configure SATA As [IDE]
Sets the configuration for the Serial ATA connectors supported by the
Southbridge chip.
If you want to use the Serial ATA hard disk drives as Parallel ATA physical
storage devices, set this item to [IDE].
Set this item to [RAID] if you want to create a RAID volume from Serial
ATA hard disk drives.
Place a jumper cap on pins 1-2 of the RAID_SEL1
R A I D _ S E L 1
R A I D _ S E L 1
R A I D _ S E L 1
R A I D _ S E L 1 jumper to use the LSI
Logic Embedded SATA RAID Utility (for RAID 0, RAID 1, or RAID 0+1
configuration; supported on Windows
®
2000/2003 Server/XP and Red
Hat
®
Enterprise ver. 3.0). Refer to section 4.2 Jumpers
4.2 Jumpers
4.2 Jumpers
4.2 Jumpers
4.2 Jumpers for details.
Place a jumper cap on pins 2-3 of the RAID_SEL1
RAID_SEL1
RAID_SEL1
RAID_SEL1
RAID_SEL1 jumper to use the Intel
®
Matrix Storage Manager (for RAID 0, RAID 1, RAID 0+1, or software RAID 5
configuration; supported on Windows
®
2000/2003 Server/XP).
IDE Configuration
ATA/IDE Configuration
[Enhanced]
Configure SATA As
[IDE]
Primary IDE Master
:
[ATAPI CD-ROM]
Primary IDE Slave
:
[Not Detected]
Secondary IDE Master
:
[Not Detected]
Secondary IDE Slave
:
[Not Detected]
Third IDE Master
:
[Not Detected]
Third IDE Slave
:
[Not Detected]
Fourth IDE Master
:
[Not Detected]
Fourth IDE Slave
:
[Hard Disk]
IDE Detect Time Out (Sec)
[35]
Select Screen
Select Item
+-
Change Option
F1
General Help
F10 Save and Exit
ESC Exit
BIOS SETUP UTILITY
Main
v02.58 (C)Copyright 1985-2004, American Megatrends, Inc.
Set[Compatible Mode]
when Legacy OS(i.e.
WIN Me, 98, NT4.0, MS
DOS)is used.
Set[Enhanced Mode]
when Native OS(i.e.
Win2000, WIN XP)is
used.
(Defaults)
