ASTi ACE Studio Cold Start Manual Download Page 55

Page: 55 / 62

12.1 Upload Options files to the RMS

ASTi ships the options file on a CD included with the system. The Options file is an archive
(i.e., tgz) file. To upload an Options file to the Remote Management System (RMS), follow
these steps:

1. From the vertical left menu, under

Configuration

, click

Options File Mgmt.

, and then

click

Choose File

2. Browse to the file on the development workstation, and click

Choose

3. Click

Upload New Options File

, and wait for the upload to complete. You can upload a

new Options file at any time.

Caution

: If you select an Options file with the same name as the currently installed

Options file, the new file overwrites the existing file.

Figure 36: Options File Mgmt.

ACE Target and Studio Cold Start Guide (Rev. B, Ver. 0)

Summary of Contents for ACE Studio































































Search results

Summary of Contents for ACE Studio

Reviews:

Related manuals for ACE Studio

Brands by name

Popular brands

ASTi ACE Studio, Cold Start Manual

Search results

Summary of Contents for ACE Studio

Reviews:

Related manuals for ACE Studio

Brands by name

Popular brands