manualshive.com logo in svg

Associated Research HYAMP II 5030DT, Operation And Service Manual

Share
Download
Associated Research HYAMP II 5030DT Operation And Service Manual Download Page 25

 

INSTALLATION

 

 

 

21

The instrument should also be protected against temperature extremes which may cause 
condensation within the instrument. 
 

Packaging

 

 
Original Packaging:  Please retain all original packaging materials if you do not have an 
alternate method of repackaging. If you are returning your instrument to us for servicing 
please repackage the instrument in its original container or use an alternate packaging 
solution. Please do not reuse the original packing material if there appears to be damage or 
missing packing material. Contact our customer support department (1-800-858-8378) for 
an RGA (return goods authorization) number.  Please enclose the instrument with all 
options, accessories and test leads.  Indicate the nature of the problem or type of service 
needed.  Also, please mark the container "FRAGILE" to insure proper handling.  Upon 
receipt your instrument will be issued an AR service number.  Please refer to this number 
in all correspondence. 
 
Other Packaging: If you do not have the original packaging materials please follow these 
guidelines: 
 
1).  Wrap the instrument in a bubble pack or similar foam.  Enclose the same information 

as above. 

 
2).  Use a strong double-wall container that is made for shipping instrumentation.  350 lb. 

test material is adequate. 

 
3).  Use a layer of shock-absorbing material 70 to 100 mm (3 to 4 inch) thick around all 

sides of the instrument.  Protect the control panel with cardboard. 

 
4).  Seal the container securely. 
 
5).  Mark the container "FRAGILE" to insure proper handling. 
 
6).  Please ship models 5030DT via Federal Express or UPS air. 
 
7).  Please refer in all correspondence to your AR service number. 
 

 
 
 
 
Field Installation Of Options   
 

There are no field installable options on the model 5030DT. 
 

Summary of Contents for HYAMP II 5030DT






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands