step 3
REAR SHOCK TOWER ASSEMBLY
Install the two #7413 screws through the
outer holes on the #3895 (3896*) rear shock
tower. Then thread on the #7260 nuts.
Attach the #3858 ball ends and #7260 nuts
through the lower inner holes on the shock
tower.
Add a #6272 dust cover to
the ball ends.
step 4
REAR SHOCK
TOWER
ASSEMBLY
Attach the #3895
(3896*) rear shock
tower to the upper
transmission case
with three #6924
(6860*) screws.
7413
7413
7260
7260
3895, 3896*
7260
7260
3858
3858
6272
6272
6924, 6860*
3895, 3896*
BAG E
REMOVE THESE
PARTS FOR:
Steps 1-4
TOOLS USED
7381, qty 4
CVD coupling
3886, qty 4
CVD axle
7381, qty 4
CVD cross pin
7381, qty 4
CVD set screw
3887 or 3888, qty 4
CVD bone
7260, qty 2
4-40 plain nut
1:1
1:1
6272, qty 2
ball end dust cover
6273, qty 2
long ball end
natural color
1:1
RACER KIT ONLY
3977, qty 4
3/16 x 3/8
rubber sealed bearing
TEAM & F.T. KITS ONLY
6906, qty 4
3/16 x 3/8
PTFE
sealed bearing
1:1
7368, qty 2
shim
7369, qty 2
CVD roll pin
3858, qty 2
long special
ball end, black
1:1
3875, qty 2
4-40 x 11/32 screw
with shoulder
3866, qty 2
front outer
hinge pin
3868, 3869*, qty 2
front block carrier
(0° caster block)
3876, 3877*, qty 2
front steering
block
6588, qty 1
black grease
1:1
1:1
1:1
1:1
1:1
3862, qty 2
5-40 set screw
gold
3874, qty 4
block carrier
bushings
1:1
1:1
1:1
1/16", .050"
3965, qty 2
bearing spacer
1:1
1:1
1:1
step 1
MIP CVD ASSEMBLY
Spread some Associated
#6588 black grease inside
the axle hole where shown,
then on the coupling and
insert the coupling into the
axle.
Slide the axle into the
dogbone, aligning the cross
holes.
Insert the cross pin, making
sure it is evenly spaced on
both sides of the bone.
Add the MIP thread lock to
the set screw. Angle and
turn the CVD so the set
screw can be screwed in
with the Allen wrench.
Repeat steps for the three
remaining CVD's.
3886 axle
step 2
STEERING BLOCK ASSEMBLY
Install one #3977 or #6906 bearing
on the axle. Slide the axle
assembly into the back of the
#3876 (3877*) steering block.
Slide in a #3965 bearing spacer.
Install the second #3977 or #6906
bearing into the steering block and
on the axle, followed by one #7368
thin spacer.
Insert the #7369 roll pin into the
axle.
Thread the
natural color
#6273
ball end into the
bottom
of the
#3876 steering block and add the
#7260 plain nut. Add a #6272 dust
cover over ball the end.
Repeat steps for the right side,
installing the steering block ball
end in the opposite way:
1:1
RACER KIT ONLY
3977, qty 4
3/16 x 3/8
rubber sealed bearing
TEAM & F.T. KITS ONLY
6906, qty 4
3/16 x 3/8
PTFE
-sealed bearing
1:1
5
6588
7381 coupling
3887 or 3888
dogbone
7381
cross pin
11
7381
set screw
7368
7369
7260
6273
6272
thread lock
3876, 3877*
LONG NATURAL
COLOR BALL END.
DO NOT
USE
THE BLACK BALL
END HERE!!
10
10
10
3965
12
