Associated Electrics SC10 4x4 Manual Download Page 45

Page: 45 / 70

:: Chassis Brace Assembly (cont.) - Bag N

:: Wheel and Tire Assembly - Bag O

Build 4!

Tire glue is

not included!

91101

KMC Hex

Wheel

(black)

89413

1/8th molded

tire insert

(RTR ONLY)

9809

SC10 Tire

w/foam

insert

(RTR ONLY)

Note: Clean the rims and tire bead

where the two will mount to each other

before you glue them together. You

can clean them with either rubbing al-

chohol, or r/c electric motor spray.

Use Tire glue #1597 to glue the tire

to the wheel. Glue one side at a time,

allowing enough time for the glue to dry

before continuing to the other side.

Tip: You can use a rubber band to hold

the tire tight against the wheel while

the glue is drying.

91184

Chassis brace

ball joint

(FT ONLY)

89209

M3x18mm

fhcs

(FT ONLY)

91184

Chassis

brace

(FT ONLY)

89211

M3x26mm

fhcs

(FT ONLY)

Snap the ball joints into

the larger hole of the

chassis brace eyelets first.

Then install the chassis

brace into the vehicle.

The two holes

shown should be

facing towards

the chassis when

installed.

Summary of Contents for SC10 4x4







































































Search results

Summary of Contents for SC10 4x4

Reviews:

Related manuals for SC10 4x4

Brands by name

Popular brands

Associated Electrics SC10 4x4, Manual

Search results

Summary of Contents for SC10 4x4

Reviews:

Related manuals for SC10 4x4

Brands by name

Popular brands