Assa Abloy Securitron Magnalock M670-313 Installation Instructions Manual Download | Manualshive

Page: 9 / 20

background image

PN#

500-10550

Page 9

Rev. D, 12/14

Installing the Magnalock

1. REMOVE the two (2) screws securing lock to mounting bracket and SLIDE the bracket from the top of

the lock chassis.

2. PINCH and INSERT spacers flush into the dovetail slots of the lock-mounting bracket.

«
...
7
8
9
10
11
...
»

Summary of Contents for Securitron Magnalock M670-313





















Reviews:

No comments

Related manuals for Securitron Magnalock M670-313

Brand: hager Pages: 4

Brand: Cal-Royal Pages: 4

Brand: Cal-Royal Pages: 12

DEADBOLT EDITION SECURE PGD728

Brand: Lockly Pages: 17

Mounting Bracket Lock

Brand: iKAMPER Pages: 5

Brand: Digitus Pages: 6

Brand: Siemens Pages: 2

Brand: Siemens Pages: 20

Codelock K44 Duo

Brand: Siemens Pages: 184

WALL KEY COMBINATION BOX

Brand: Viro Pages: 2

Brand: tapplock Pages: 24

Brand: OLDA Innovation Pages: 2

Real Living Assure Lock

Brand: Yale Pages: 48

Brand: ZK Software Pages: 20

Brand: JNF Pages: 16

Brand: SARGEANT & GREENLEAF Pages: 4

Brand: Von Duprin Pages: 5

Brand: ZKTeco Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands