manualshive.com logo in svg

Assa Abloy Norton 6000 Series, Programming Instructions Manual

Share
Download
Assa Abloy Norton 6000 Series Programming Instructions Manual Download Page 22

80-9360-1043-020  Rev 1  05/21

Copyright © 2021, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or 

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

22

6000 Series

 Wiring Diagrams

24VDC Fail Safe Electric Strike or Electromagnetic Lock

(change factory pre-wiring to illustration below - move NO to NC on controller)

•  Door is normally closed and latched.

•  Activating switch will unlock electric strike or mag lock and door will 

automatically open. Door will close after hold open time delay has expired.

•  Door will remain unlocked during power failure.

•  Activation can be wall switch, card reader, key switch, etc (Normally open 

momentary dry contacts).

•  Current draw at Power Outputs not to exceed 1.3A.

•  To turn on relay (Relay 2), Latch Retraction (Output 

Connections, page 14) and/or Open Delay (Set options, 

page 8) features must be turned on using adjustment 

procedures on pages indicated.

Summary of Contents for Norton 6000 Series



































Reviews:

No comments

Brands by name

Popular brands

Load more brands