manualshive.com logo in svg

Assa Abloy Norton 6000 Series, Programming Instructions Manual

Share
Download
Assa Abloy Norton 6000 Series Programming Instructions Manual Download Page 21

80-9360-1043-020  Rev 1  05/21

Copyright © 2021, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or 

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

21

6000 Series

 Wiring Diagrams

24VDC Fail Secure Electric Strike or Electric Exit Device

•  Door is normally closed and latched.

•  Activating switch will unlock electric strike 

or exit device and door will automatically 

open. Door will close after hold open time 

delay has expired.

•  Door will remain locked during power 

failure.

•  Activation can be wall switch, card reader, 

key switch, etc (Normally open momentary 

dry contacts).

•  To turn on relay (Relay 2), Latch Retraction 

(Output Connections, page 14) and/or 

Open Delay (Set options, page 8) features 

must be turned on using adjustment 

procedures on pages indicated.

Summary of Contents for Norton 6000 Series



































Reviews:

No comments

Brands by name

Popular brands

Load more brands