background image

of 8

Printed in the U.S.A.

Patent pending and/or patent www.assaabloydss.com/patents 

Copyright © 2022, Hanchett Entry Systems, Inc., an ASSA ABLOY Group company. 

All rights reserved. Reproduction in whole or in part without the express written 

permission of Hanchett Entry Systems, Inc. is prohibited.   80-0180-497_1

adamsrite.com  |  

800  626  7590

 

[email protected]
10027 S. 51st Street, Ste. 102 Phoenix, AZ 85044  USA

WARNING

FCC Statement

This equipment has been tested and found to 

comply with the limits for a class B digital device, 

pursuant to part 15 of the FCC Rules. These limits are 

designed to provide reasonable protection against 

harmful interference in a residential installation. This 

equipment generates, uses, and can radiate radio 

frequency energy and if not installed and used in 

accordance with the instructions, may cause harmful 

interference to radio communications. However, there 

is no guarantee that interference will not occur in a 

particular installation. If this equipment does cause 

harmful interference to radio or television reception, 

which can be determined by turning the equipment 

off and on, the user is encouraged to try to correct the 

interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2.  Increase the separation between 

the equipment and receiver.

3.  Connect the equipment into an outlet 

on a circuit different from that to 

which the receiver is connected.

4.  Consult the dealer or an experienced 

radio/TV technician for help.

Operation with non-approved equipment is likely to 

result in interference to radio and TV reception. The 

user is cautioned that changes and modifications 

made to the equipment without the approval of 

manufacturer could void the user’s authority to 

operate this equipment. To comply with FCC and 

Industry Canada RF radiation exposure limits for 

general population, the module must be installed to 

provide a separation distance of at least 20cm from 

all persons and must not be colocated or operating in 

conjunction with any other antenna or transmitter.
This module is labeled with its own FCC ID and 

IC Certification Number. If the FCC ID and IC 

Certification Number are not visible when the module 

is installed inside another device, then the outside 

of the device into which the module is installed 

must also display a label referring to the enclosed 

module. In that case, the final end product must 

be labeled in a visible area with the following:
Contains FCC ID: VC3-R100V3
Contains IC: 7160A-R100V3

IC Statement

This device complies with Industry Canada 

license-exempt RSS standards(s). Operation 

is subject to the following two conditions:
(1) this device may not cause interference, and
(2)  this device must accept any interference, including 

interference that may cause undesired operation.

Conformité aux normes IC

Cet appareil est confrome avec Industrie Canada 

exempt de license RSS standard(s). Son fonctionnement 

est souimes aux deux conditions suivantes:
(1)  cet appareil ne peut causer d’interférences, et
(2)  cet appareil doit accepter toute interference, y 

compris des interférences qui peuvent provoquer 

un fonctionnement indésirable du périphérique.

CE Declaration of Conformity

content.assaabloyusa.com/doc/AADSS1179512&.pdf

Product Specifications

Approvals

CE, FCC, IC

Wireless Frequency

2.4GHz, IEEE 802.15.4, using AES 128-bit encryption

AA Lithium

Energizer L91 Rated 1.5 VDC, 3 Ah

NOTE: Replace Battery With Energizer L91 

batteries only.  Use of another battery may 

present a risk of fire or explosion.  

CAUTION: Risk of fire and burns. Do not recharge, 

disassemble, heat above operating temperature 

or incinerate. Keep battery out of reach of 

children and in original package until ready 

to use. Dispose of used batteries promptly.

Battery Life

2+ years (45,0000 cycles)*
*All battery life claims are approximate and based 

on a set configuration profile. Battery performance 

is based on pre-defined system settings such 

as battery chemistry and battery model used, 

credential presentation settings (LED/buzzer), 

UHF polling period, UHF status intervals, and 

operations per day. Actual battery performance 

will vary and depends on the factors above.

HID® multiCLASS SE® Technology 

Credentials Supported

• High Frequency (13.56 MHz)
• HID iCLASS®
• HID iCLASS SE® (SIO-enabled)
• HID iCLASS® Seos™
• HID MIFARE® SE
• HID DESfire® EV1 SE
• MIFARE CLASSIC
• DESfire® EV1
• 

Low Frequency (125 kHz)

• HID Prox®, AWID, EM4102, ioProx

NFC/BLE*

Mobile – enabled credentials 

Reader is compatible with HID Mobile 

Access version 3.76 and later using mobile 

devices with BLE version 4.2 and later

Environmental

Operating Temperature 

(both products)

• 14° to 140° F [-10° to 60° C]

Operating Humidity 

(both products)

• 0 to 93% relative humidity non-condensing

Certifications

• UL 294 Listed – Indoor Rated
• UL 294 Salt Spray Test Compliant
• Tested to IP65 (Reader Only)
• FCC Part 15 & Industry Canada Compliant
• CE RED – Radio Equipment Directive – 2014/53/EU

UL294 Performance Levels

• Destructive

 

Attack:

 Level I (No Attack Test)

• Line Security: 

Level I (No Line Security)

• Endurance:

 Level IV (100,000 Cycles)

• Standby Power:

 Level I (No Secondary Power)

Safety and Emissions

• FCC 47CFR Part 15, subpart C 
• IC RSS-102
• RSS-210
• RSS-247
• RE Directive 2014/53/EU, EN 301 489-1, EN 301 489-3,  

EN 300 440, EN 300 330, EN 300 328, EN 62368-1, EN 62479

Summary of Contents for Adams Rite DL100









Reviews: