background image

© by ASM GmbH 

 

MAN-PRDS-E-17         3

www.asm-sensor.com  / USA: www.asmsensors.com

Safety  

instructions

POSIROT

®

 –  PRDS

Safety instructions

If total failure or malfunction of the sensor can cause danger or 

injury to the operator or damage to the machinery or equipment 

it is recommended that additional safety measures should be 

incorporated into the system. 

Any alteration, reconstruction or extension of the sensor is not 

allowed.

Sensor  must  be  operated  only  within  values  specified  in  the 

datasheet.

Connection to power supply must be performed in accordance 

with safety instructions for electrical facilities and performed 

only by trained staff.

Do not connect / disconnect the sensor under tension.

Disregard of this advice can lead to malfunctions, damage to 

property or personal injury and releases the manufacturer from 

product liability.

Explanation of used 

safety signs and 

signal words

WARNING, Risk of Injury: 

Indicates a potentially hazardous situation, which, if 

not avoided, could result in serious injury or property 

damage. 

  

WARNING, Risk of Personal Injury or Death: 

Indicates a situation that can result in serious personal 

injury or death if not properly avoided.

DANGER

WARNING, Risk of Personal Injury or Death: 

Indicates a situation that can result in moderate 

personal injury or death if not properly avoided.

WARNING

WARNING, Risk of Personal Injury: 

Indicates a situation that can result in minor personal 

injury if not properly avoided.

CAUTION

WARNING, Risk of Property Damage: 

Indicates a situation that can result in minor to major 

property damage if not properly avoided.

NOTICE

Summary of Contents for POSIROT Series





















































Reviews: