Asko WM25 Service Manual Download Page 16

Servicemanual WM25

Action type

Motor action

Inlet valves

Level table

U-level/Volt

1,04

1,12

1,58

1,84

2,32

2,75

3,32

1,36

,,,,,,,,,,,,,,,,

Timer diagram, table explanation

P11-P18

P6

P7

P8

P9

P1

P3

P4

P5

2

3

4

Fill-action

SSG

G*

Valve

1

NF

N

G

SG

WT

TD

S

TO

D

T

H

HD

F

TF

¹)

If P3 not has been reached within 2`, these steps will follow:
• 3`` no action
• 1` trying to reach P3

Definition

Safety: heater door opening

Drain level

Refill pre-soak and wool

Rinse level

Fill level pre-soak and wool

Reset level over-flow

Over-flow level

Identical to T-action except for the definition of the step-time. Specified step-time reduced with previos F-action or H-action

Normal wash level

Main wash (cold water)

Super gentle action: Clockwise 3 seconds on 57 seconds off, counterclockwise 3 seconds on 57 seconds off. 49rpm

Super super gentle action: Same as SG except motion, 40rpm

Pre-soak action: 1 minut off G-action, 10 minutes no motion

Refill pre-wash & main wash 

Spin-action

Normal fill action: Clockwise 9 seconds on 6 seconds off, counterclockwise 9 seconds on 6 seconds off.  40rpm

Normal action: Clockwise 12 seconds on 3 seconds off, counterclockwise 12 seconds on 3 seconds off. 49rpm

Gentle action: Clockwise 3 seconds on 27 seconds off, counterclockwise 3 second on 27 seconds off. 49rpm

Main wash (hot water)

Final rinse (for rinse agent)

Time out

Definition

Pre-soak, pre-wash and rinses

Thermostop-step that heats up to selected temperature. The step will end when selected temperature is reached

Time controlled heat-step. Heats to selected temperature or to specified time elapses

The time in this step is depending of numbers of refills in the filling step

Option

Factory settings

Fill action fills up to the specified level

Fills for selected time, if selected level is not reached within the time, continue to fill to selected level is reached

Drain action, which pumps until specified level is r 30 seconds. If specfied level is reached within time, skip the light blue steps

Time action that executes level-control and motion as specified. Motor motion when water level exceeds. During refilling no motor motion

Appendix: Timer diagram

Page 3

Summary of Contents for WM25

















Reviews: