background image

Page 6

Customer Care Center

1-800-898-1879

www.askona.com

WARNING!

Before working on wiring for any electrical appliance, 
be sure the electrical power has been turned off at 
the breaker/fuse box.

WARNING!

Disconnect the electrical power supply and place a 
tag at the disconnect switch indicating that you are 
working on the circuit.

WARNING!

Electrical and grounding connections must comply 
with the applicable portions of the 
national electrical code and/or other local 
electrical codes.

The dishwasher comes with an electrical 

cord for 120 volts, 15 amp supplied. This cord should 

be plugged into the 120 volt outlet under the sink.
If the cord is not long enough, or if a hard-wire installation 

is needed, follow instructions on page 8.

NOTE: 

Access holes should be 1-1/2˝ (38 mm) in diameter 

with no sharp edges.

PERMANENTLY-CONNECTED APPLIANCE 

GROUNDING INSTRUCTIONS

This unit must be grounded to operate properly. It must 

be connected to a grounded metal, permanent wiring 

system, or an equipment-grounding conductor must 

be run with the circuit conductors and connected to the 

equipment-grounding terminal or lead of the appliance.
Damage to the dishwasher could occur if it is not properly 

grounded.

WARNING!

Make sure the water supply line, drain line and branch 
circuit wiring do not touch any exposed terminals of 
dishwasher wiring.

185

7

CORD-CONNECTED APPLIANCE

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of a 

malfunction or breakdown, grounding will reduce the risk 

of electric shock by providing a path of least resistance 

for electric current. This appliance is equipped with a 

cord having an equipment-grouding conductor and 

a grounding plug. The plug must be plugged into 

an appropriate outlet that is installed and grouded in 

accordance with all local codes and ordinances.

WARNING!

Improper connection of the equipment-grounding 
conductor can result in a risk of electric shock. Check 
with a qualified electrican or service representative 
if you are in doubt whether the appliance is properly 
grounded. Do not modify the plug provided with the 
appliance, if it will not fit the outlet, have proper outlet 
installed by a qualified electrician.

WARNING!

Risk of electric shock. Do not use an extension cord 
for this appliance.

Connect dishwasher cord directly to a dedicated outlet 

suitable for installation in damp or wet locations and 

protected by a Ground-Fault Circuit-Interrupter (GFCI) in 

accordance with local codes. If an outlet is not provided, 

contact a qualified electrician for proper installation.

ELECTRICAL CONNECTIONS

492161 Install DW Outdoor USA EN Rev 01.indd   6

2014-10-01   13:17:42

Summary of Contents for D5954OUTDOORPH













Reviews: