background image

Page 3

Customer Care Center

1-800-898-1879

www.askona.com

OPERATING ENVIRONMENT

Do not place this appliance (including the PEX fill hose 

and drain hose) where it will be hit by direct sunlight or 

exposed to extreme weather conditions.
Do not place the outdoor dishwasher close to a 

swimming pool. Water splashing on the machine’s 

surfaces can ultimately lead to corrosion (rust).
This appliance is designed to operate outdoors. It is set 

to operate within the ambient temperature limits between 

50 °F (10 °C) and 104 °F (40 °C). These temperature 

limits should not be exceeded.

BUILT-IN INSTALLATION

The dishwasher can be installed in a cabinet, or 

completely freestanding. See the illustration to the right 

for cutout dimensions.
The best place for your dishwasher is in the kitchen near 

the sink. This makes it easier to connect the water and 

drain supply lines.
The power-supply receptacle for the appliance shall 

be installed in a cabinet or on a wall adjacent to the 

undercounter space in whitch the appliance is to be 

installed.
The electrical and water supplies should enter through 

the area indicated by the shading on the illustration at 

right. Preferably, they should come through the right side 

of the machine. The access hole must be round and 

smooth and no bigger than 1-1/2˝ (38 mm) in diameter. 

If the partition is metal, it needs to be covered with 

an edge protector and care shall be exercised, when 

the appliance is installed or removed, to reduce the 

likelihood of damage to the power-supply cord.

U.S.

Metric

Height (Adjustable) 

35˝ to 35-3/4˝

889 to 908mm

Width 

24-5/8˝  

625 mm

Depth (Includes high loop) 25˝  

635 mm

DepthW/handle

27˝

686 mm

Depth W/Door Open

51-5/8˝

 

1311 mm

Weight

163 Ib

74 kg

U.S.

Metric

Height 

35-1/4˝ to 36˝

895 to 914mm

Width  

24-7/8˝ 

632 mm

Depth

25-1/4˝

641 mm

24-7/8"

632 mm

25-1/4˝

641 mm

127 mm

5-3/4˝

146 mm

895-914 mm

51 mm

35-1/4˝ to 36˝ minimum

Cutout Dimensions

UNIT DIMENSIONS

Electricity 

120 V, 60 Hz, 15 amp

Water pressure

4.2 - 140 psi, 
0.03-1.0 MPa,
0.3-10 Bar

Heating element

1200 watt 

Max loading

1300 watt

Technical Data

Door

5-3/4" to 6-5/8" 

146 mm to 168 mm 

24-5/8"

625 mm

3-1/2"
89 mm

3-7/8"
98 mm

35" to 35-3/4" 

889 to 908 mm 

4-7/8"
124 mm

25"

635 mm

27"

686 mm

51-5/8"
1311 mm

9-1/2"

241 mm

PREPARING THE LOCATION

NOTE:

Maintain a 1/8˝ (3 mm) minimum clearance between 

unit and cabinet.

492161 Install DW Outdoor USA EN Rev 01.indd   3

2014-10-01   13:17:40

Summary of Contents for D5954OUTDOORPH













Reviews: