background image

Page 4

Customer Care Center

1-800-898-1879

www.askona.com

WARNING!

Plumbing connections must comply with applicable 
sanitary, safety and plumbing codes in your area. 

The machine can be connected to either a hot (max. 160 

°F, 70 °C) or cold water supply. We recommend a cold 

water supply. The water pressure should be 4.2-140 psi.

Connect to cold water...

If you use oil or electricity to heat your home.

Connect to hot water (max 160 °F, 70 °C)... 

If you use district heating, solar power, or geothermal 

power to heat your home. Choosing a hot water 

connection cuts program times and reduces the 

dishwasher’s electricity consumption.

PEX tubing with 3/8˝ compression 
fitting

PEX tubing has a 95-year spec life. 

Fits American dishwasher water 

supply valves. Be sure to install the 

O-Ring which is attached to the PEX 

tubing in a plastic bag

Drain hose boot

Ready to be cut to desired 

drain connection. Only 

one clamp required.

NOTE:

Be sure to run the PEX tubing through the hole to the 

sink compartment before moving the dishwasher into 

position.

(1) Water supply
(2) Water supply valve to dishwasher (not supplied)

The dishwasher comes with a 6-foot PEX water supply 

line that has a 3/8˝ NPT female connection.
After determining where the water supply line will enter 

under the sink, drill a 1-1/2˝ (38 mm) access hole and 

run the line to the approximate inlet valve location shown 

in the figure below. The water line inlet valve is on the 

right rear of the machine.
For service convenience, a shut-off valve (not supplied) 

should be installed in the supply line in an easily 

accessible location, such as, beneath the sink.
It is important that the water supply line and the shut-off 

valve have a sufficient flow volume. At least 3 gallons 

(12 liters) per minute must be able to pass through the 

line. The water pressure should be 4.2-140 psi.

WARNING!

In order to prevent heat damage to the inlet valve, all 
solder connections must be made before the water 
line is connected to the dishwasher.

WATER SUPPLY

Electrical cord

120 volts, 15 amp cord is supplied with 

the dishwasher.

WARNING!

Risk of electric shock. Do not use an extension cord 
for this appliance.

EASYINSTALL CONNECTIONS

492161 Install DW Outdoor USA EN Rev 01.indd   4

2014-10-01   13:17:41

Summary of Contents for D5954OUTDOORPH













Reviews: