ASI ALPACO ELEGANCE Installation Instructions Manual Download Page 13

ALPACO ELEGANCE INSTALLATION 

Page 12 

CARE AND MAINTENANCE OF 

BATHROOM PARTITIONS 

In  order  to  provide  bathroom  partitions  with  proper  care  and  maintenance,  the 

following instructions must be followed: 

A. All surfaces must be kept clean with water and a mild soap solution only.

B. In areas of high humidity, the rooms must be properly ventilated.

C. “Hosing down” or wet-washing of these units may cause water adsorption and damage.

D. For maximum protection, periodic application of any standard furniture wax will be

beneficial.

WARNING 

Under no circumstances should these components be subjected to: 

Abrasive powders or pads

Bathroom cleaners

Ceramic tile cleaners

Solutions containing more than 1% by volume of ammonia

Solutions containing acids or lye

Solutions containing enzymes

Attention to work progress during new construction or renovation is paramount. 

Some cleaning services may use agents for ceramics and tiles that will damage these 

components. 

160 Tower Drive

, Burr Ridge,

 IL 6052

7

     Phone: (708) 442-6800     Fax: (708) 442-7439

www.asi-accuratepartitions.com

Summary of Contents for ALPACO ELEGANCE














Reviews: