© 2021 United States Stove Company
15
3.
Install right bottom log (#3) on right log support
bracket in front of back log.
Left Bottom
Log #2
Back Log #1
Top Left
Log #4
Right
Bottom
Log #3
Right
Bottom
Log #3
Right
Bottom
Log #3
Right Top
Log #5
Rear Log
Support
Bracket
Left Log
Support
Bracket
Right Log
Support Bracket
PILO
T
OFF
Left Bottom
Log #2
Back Log #1
Right Top
Log #5
PILO
T
OFF
Left Bottom
Log #2
Back Log #1
Top Left
Log #4
Right Top
Log #5
PILO
T
OFF
Back Log #1
Top Left
Log #4
Right Top
Log #5
PILO
T
OFF
Log #5
PILO
T
OFF
PILO
T
OFF
Left Bottom
Log #2
Back Log #1
Left Bottom
Log #2
Top Left
Log #4
Log #4
Back Log #1
Top Left
Log #4
Log Support
Bracket Studs
Burner Ports
Left Bottom
Log #2
Right
Bottom
Log #3
Right
Bottom
Log #3
Right
Bottom
Log #3
Log #5
Top Left
4.
Install top left log (#4) on top of left bottom log.
Left Bottom
Log #2
Back Log #1
Top Left
Log #4
Right
Bottom
Log #3
Right
Bottom
Log #3
Right
Bottom
Log #3
Right Top
Log #5
Rear Log
Support
Bracket
Left Log
Support
Bracket
Right Log
Support Bracket
PILO
T
OFF
Left Bottom
Log #2
Back Log #1
Right Top
Log #5
PILO
T
OFF
Left Bottom
Log #2
Back Log #1
Top Left
Log #4
Right Top
Log #5
PILO
T
OFF
Back Log #1
Top Left
Log #4
Right Top
Log #5
PILO
T
OFF
Log #5
PILO
T
OFF
PILO
T
OFF
Left Bottom
Log #2
Back Log #1
Left Bottom
Log #2
Top Left
Log #4
Log #4
Back Log #1
Top Left
Log #4
Log Support
Bracket Studs
Burner Ports
Left Bottom
Log #2
Right
Bottom
Log #3
Right
Bottom
Log #3
Right
Bottom
Log #3
Log #5
Top Left
5.
Install top right log (#5) on top of right bottom
log.
Left Bottom
Log #2
Back Log #1
Top Left
Log #4
Right
Bottom
Log #3
Right
Bottom
Log #3
Right
Bottom
Log #3
Right Top
Log #5
Rear Log
Support
Bracket
Left Log
Support
Bracket
Right Log
Support Bracket
PILO
T
OFF
Left Bottom
Log #2
Back Log #1
Right Top
Log #5
PILO
T
OFF
Left Bottom
Log #2
Back Log #1
Top Left
Log #4
Right Top
Log #5
PILO
T
OFF
Back Log #1
Top Left
Log #4
Right Top
Log #5
PILO
T
OFF
Log #5
PILO
T
OFF
PILO
T
OFF
Left Bottom
Log #2
Back Log #1
Left Bottom
Log #2
Top Left
Log #4
Log #4
Back Log #1
Top Left
Log #4
Log Support
Bracket Studs
Burner Ports
Left Bottom
Log #2
Right
Bottom
Log #3
Right
Bottom
Log #3
Right
Bottom
Log #3
Log #5
Top Left
CAUTION:
DURING INITIAL OPERATION OF THE NEW
HEATER, BURNING LOGS WILL GIVE OFF
A PAPER BURNING SMELL AND ORANGE
FLAMES WILL BE PRESENT. SIMPLY OPEN THE
WINDOWS FOR A FEW HOURS TO VENT THE
ODOR.
GLOWING WOOL PLACEMENT
Provided with your log set is a package of Glowing
Embers (rock wool). Break up the glowing wool into
small dime sized pieces or for a finer finish use a
metal wire brush. Place it over the small holes (ports)
located on the burner pan. Cover the entire section
of holes (ports).*Replacement of loose (Glowing
Wool) must be purchased from the original
manufacturer and application of excess loose
material may adversely affect the performance of
the heater. NOTE: Wash your hands immediately
after coming in contact with wool material. In some
cases the wool can cause slight itching or burning,
avoid any contact with eyes.
WARNING:
All previously applied loose material must be
removed prior to replacement. Do not cover the
air channels with the glowing wool.
FLAME APPEARANCE
Flames from the pilot, front and rear burner should
be visually checked as soon as the heater is installed.
In addition, periodically check the flames visually
during operation.
PILOT FLAME
The pilot flame must always be present when the
heater is in operation. It should just touch the top of
the thermocouple tip for natural. Refer to the figure
below for correct pilot flame.
If the pilot flame does not touch the thermocouple,
then the burners cannot function reliably. Refer to
the figure below for incorrect shape of pilot flame.
LOG PLACEMENT
