Ascon Tecnologic - KX6 - ENGINEERING MANUAL -
PAG. 24
]
LBA group - Loop Break Alarm Parameters
no. Param.
Description
Dec.
Point
Values
Default
35
LbAt
LBA time
0
From 0 (oFF) to 9999 (s)
oFF
36
LbSt
Delta measure used by LBA during Soft start dP
From 0 (oFF) to 9999 (E.U.)
10
37
LbAS
Delta measure used by LBA
dP
1...9999 (E.U.)
20
38
LbcA
Condition for LBA enabling
0
uP
Active when Pout = 100%;
dn
Active when Pout = -100%;
both
Active in both cases.
both
]
rEG group - Control Parameters
no. Param.
Description
Dec.
Point
Values
Default
39
cont
Control type
(when the controller is equipped
with digital outputs)
Pid
PID (Single or double action);
On.FA ON/OFF asymmetric (Single action);
On.FS ON/OFF symmetric (Single action);
nr
ON/OFF double action with neutral zone;
3Pt
Servomotor control (Out 1 = open, Out 2 = close).
40
Auto
Autotuning selection
0
-4 Oscillating auto-tune with automatic restart at power up and
after all point change;
-3 Oscillating auto-tune with manual start;
-2 Oscillating -tune with automatic start at the first power up only;
-1 Oscillating auto-tune with automatic restart at every power up;
0 Not used;
1 Fast auto tuning with automatic restart at every power up;
2 Fast auto-tune with automatic start the first power up only;
3 FAST auto-tune with manual start;
4 FAST auto-tune with automatic restart at power up and
after a set point change;
5 Evo-tune with automatic restart at every power up;
6 Evo-tune with automatic start the first power up only;
7 Evo-tune with manual start;
8 Evo-tune with automatic restart at power up and after a set
point change.
7
41
tunE
Manual start of the Autotuning
0
oFF
Not active;
on Active
oFF
42
hSet
Hysteresis of the ON/OFF control
dP
0... 9999 (E.U.)
43
Pb
Proportional band
dP
1... 9999 (E.U.)
50
44
ti
Integral time
0
From 0 (oFF) to 9999 (s)
200
45
td
Derivative time
0
From 0 (oFF) to 9999 (s)
50
46
Fuoc
Fuzzy overshoot control
2
0.00... 2.00
0.50
47
tch
Heating output cycle time
1
0.1... 130.0 (s)
20.0
48
rcG
Power ratio between heating and
cooling action
2
0.01... 99.99
1.0
49
tcc
Cooling output cycle time
1
0.1... 130.0 (s)
20.0
50
rS
Manual reset (Integral pre-load)
1
-100.0... +100.0 (%)
0.0
51
Str.t
Servomotor stroke time
0
5... 300 seconds
60
52
db.S
Servomotor dead band
0
0...100%
50
53
oP.L
Minimum Power Output
From 100 to OP.H%
54
oP.H
Maximum Power Output
From OP.L to 100%
55
St.P
Maximum power output used during
soft start
0
-100... 100 (%)
0
56
SSt
Soft start time
2
0.00
oFF;
0.01... 7.59 (hh.mm);
inF
Always ON.
oFF
57
SS.tH
Threshold for soft start disabling
dP
-1999... +9999 (E.U.)
9999
58
Pot
Potentiometer enabling
nonE
Potentiometer not used;
Pot.o
Potentiometer used for indication only;
Pot.c
Potentiometer used for feedback control
59
P.caL
Automatic potentiometer calibration
no
The automatic potentiometer calibration is disabled;
YES
The automatic potentiometer calibration is enabled.
