background image

Operating Instructions for Ascoline 700, AGB 23x, AGB 43x 

ascobloc 

Gastro-Gerätebau GmbH 

01156 Dresden, Grüner Weg 29 

Germany 

Tel.: +49 351 4533-0 

Fax: +49 351 4537-339 

E-mail: 

[email protected]

,  

AEBx30ff.doc Version: 21/02/2011 

Subject to change without notice! 

 

 

The  pilot  burner  nozzle 

(C)

  is  situated  underneath  the  pilot  burner.  Unscrew  the  pilot  gas  line  from  the 

floor and pull gently downwards. Change the ignition nozzle at the end of the ignition gas line and screw 
on again. 

 

Once the conversion is completed, the appliance must be subjected to a complete test just as if it were an 
initial commissioning! 

 

10 

Umstellanleitung Gas - Bratplatte 

C

B

A

Zündbrenner mit

Zündbrennerkappe

Hauptdüse

Kleinbranddüse

Gashahn PEL 21S

Schlauchleitung

Flachdichtung

Brennerdeckel

Überwurfmutter M16x1,5 SW 19

Doppelkegelring 10 mm

Verschlußschraube SW 14
Steckschlüssel SW 5,5

Thermoelement

Zündgasleitung

Burner cover 

Thermocouple 

Screw plug A/F 14 

Socket spanner A/F 5.5 

Cap nut, M16x1.5 A/F 19 

Olive, 10 mm 

Hose piping 

Gas valve PEL 21 S 

Pilot gas line 

Low flame nozzle 

Main nozzle 

Pilot burner with pilot 
burner cap 

Flat gasket 

Conversion instructions, gas frying plate 

Summary of Contents for AGB 23 Series












Reviews: