Asada BEAVER 8 Instruction Manual Download

Page: 2 / 28

BEAVER 8･8F

Splashing

SAFETY PRECAUTIONS

Thank you for choosing our Band Saw Beaver 8 / 8F.

*This Instruction Manual must be retained by the user of this machine.

*Read this Instruction Manual carefully and completely before use and thoroughly understand the usage, capacity,cautions,

and easy repairs for correct operation.

*Handle the machine properly to make full use of its functions for safe work.

*After reading the instructions, save this manual so that you can read it when necessary.

*Use the machine for the intended application only. It will do a better job and be safer at the rate for which it was designed.

*Upon receiving the machine, check the following.

- Check that the machine is built conforming to the specifications stated in your order.

- Check the overall machine for any damage or deformation caused in transit due to accidents or other reasons.

- Check that all items and accessories delivered.

In case any discrepancy is found, immediately report the fact to the shop you purchased or our sale office.

(The contents of this manual are subject to change without prior notice.)

CLASSIFICATION OF CAUTIONS

Precautionary signs are classified into the following 3 levels

Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury. It may also be used to alert against
unsafe practices.

SYMBOLS

Electric

Shock

Cutting

Blade

High Tem-

perature

Rotation

parts

Instruction

manual

Other

Earth

Falling

Fire

Explosion

Mask

Pinching

Dragging

Summary of Contents for BEAVER 8




























Search results

Summary of Contents for BEAVER 8

Reviews:

Related manuals for BEAVER 8

Brands by name

Popular brands

Asada BEAVER 8, Instruction Manual

Search results

Summary of Contents for BEAVER 8

Reviews:

Related manuals for BEAVER 8

Brands by name

Popular brands