background image

- 14 - 

WARRANTY INFORMATION 

 
 

Limited Warranty 

 
Applied Research and Technology will provide warranty and service for this 
unit in accordance with the following warrants: 
 
Applied Research and Technology, (A R T) warrants to the original 
purchaser that this product and the components thereof will be free from 
defects in workmanship and materials for a period of 

three

 years from the 

date of purchase. Applied Research and Technology will, without charge, 
repair or replace, at its option, defective product or component parts upon 
prepaid delivery to the factory service department or authorized service 
center, accompanied by proof of purchase date in the form of a valid sales 
receipt. 

 
Exclusions:  

 
This warranty does not apply in the event of misuse or abuse of the product 
or as a result of unauthorized alterations or repairs. This warranty is void if 
the serial number is altered, defaced, or removed. 
 
A R T reserves the right to make changes in design or make additions to or 
improvements upon this product without any obligation to install the same 
on products previously manufactured. 
 
A R T shall not be liable for any consequential damages, including without 
limitation damages resulting from loss of use. Some states do not allow 
limitations of incidental or consequential damages, so the above limitation or 
exclusion may not apply to you. This warranty gives you specific rights and 
you may have other rights, which vary, from state to state. 
 
For units purchased outside the United States, an authorized distributor of 
Applied Research and Technology will provide service.

Summary of Contents for SLA-2

















Reviews: