background image

Amplifier

Amplifier

Installation

Guide

stallatio

stallat

Mobile Wireless
iDEN 
Amplifi er

Contents:

Guarantee and Warranty · · · · · · · · · · · · · · · · · · · · · · · ·  1
How it Works  · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·   2
Before Getting Started  · · · · · · · · · · · · · · · · · · · · · · · · · ·   3 
Installing a Wilson Outside Antenna  · · · · · · · · · · · · · · ·   4
Installing a Wilson Amplifi er · · · · · · · · · · · · · · · · · · · · · ·  5
Installing the Low-Profi le Antenna · · · · · · · · · · · · · · · · ·  6
Powering Up a Wilson Amplifi er · · · · · · · · · · · · · · · · · · ·  7 
Warnings and Recommendations · · · · · · · · · · · · · · · · · 

Understanding the Amplifi er Lights · · · · · · · · · · · · · · · · ·  9
About Wilson Electronics · · · · · · · · · · · · · · · · · · · · · · · ·  10
Amplifi er Specifi cations  · · · · · · · · · · · · · · · · · ·  Back Cover

Wilson

®

         Electronics, Inc.

Warning: 

This manual contains 

important safety and operating information. 
Please read and follow the instructions 
in this manual. Failure to do so could be 
hazardous and result in damage to your 
amplifi er.

!

Summary of Contents for iDEN













Reviews: