Arrow T50DCD User Manual Download Page 5

Fig 2

Fig 1

Fig 3a

POWER TOOL OPERATION

8

9

ASSEMBLY

1. 

Make sure you have read all safety instructions. 

2.

 This tool comes completely assembled. There is no assembly required.

LOADING STAPLES

1.

 Make sure tool is powered off.  

2.

  The T50DCD™ has a bottom load staple magazine. Turn tool upside down  

and squeeze pusher assembly

 

(Fig 1)

.

3.

 Pull pusher assembly out until it stops to reveal the staple magazine 

(Fig 2)

.

4.

  

STAPLES:

 Place staples into magazine with the points facing up and out of the 

tool 

(Fig 3a)

. Never attempt to completely remove pusher assembly as this may 

damage the tool and void the warranty. Close pusher assembly until it snaps 

into place.

FIRING YOUR TOOL

 

1.

  To fire your tool, place down on your workpiece depressing the contact safety 

on the front of the tool. Once the contact safety is depressed, push the trigger  

to fire your staple. You must pick up the front of the tool and reactivate the 

contact safety for each shot. The tool will operate in low temperatures down  

to 32°F (0°C) and in higher temperatures up to 104°F (40°C).

HOW TO DETERMINE PROPER STAPLE LEG SIZE 

In choosing the proper staple leg length for a job, there are two basic things 

to consider:

1.

 Thickness of material to be stapled.

2.

   Hardness of the wood. 

 

As a general rule, in hardwood, approximately 3/16” to 1/4”penetration  

into the wood is sufficient...and for softwood, up to approximately 3/8”should 

be sufficient. The staple should be flush with the underlying surface, as shown  

in Figure 4b. However, if the staple used is not flush with the underlying surface, 

as shown in Figure 4a – this means that too long a leg length has been used. 

In that case, we recommend the next shorter leg length for desired results.

A WORD ABOUT ARROW

®

 STAPLES

Only Arrow

®

 knows the proper staple tolerances required for best performance of 

the T50DCD™ Electric Stapler. Only Arrow

®

 T50

® 

staples are made to these exact 

tolerances to ensure top fastening performance. Accept no substitutes. Always insist 

on Arrow

®

 staples.

POWER TOOL OPERATION

On very hard 

surfaces, firing 

recoil may 

interfere with 

nail/staple 

penetration. 

Enhance driving 

power by firmly 

placing one hand 

on top of cap. 

Fig 4a

Fig 4b

Summary of Contents for T50DCD




















Reviews: