Arrow 697.68619 B1 Owner'S Manual & Assembly Instructions Download Page 24

Page: 24 / 36

Each screw and bolt in the wall

requires a washer.

Slide side siding into channels

of corner and splice posts, fl at edge

upward, bottom edge down resting

on fl oor frame. Always follow this

pattern. Fasten bottom edge and tab

of stud to fl oor frame using screws.

Fasten center to stud with screws.

Do not fasten top edge yet.

Install side siding as before.

Note how the slot in bottom edge

must overlap fl at edge of last siding.

Fasten both siding panels to stud at

this overlap.

Install side siding to the top as

before.

From inside building, fasten siding

to corner posts and splice post using

screws.

Repeat steps 1 through 4 opposite

side of building.

NOTE

Be careful to install the correct

panel in each position as shown.

The fl oor frame must be square

and level or holes will not align.

6287 Side Siding (12)

Parts Needed For

Side Siding

Step 11

SX24 ctr

STEP

Bottom

Edge

FRONT

Flat

Edge

Be certain all siding

overlaps are fastened

with a single screw

6287

End

View

Washer

THIS SCREW MUST

FASTEN TAB OF STUD

6287

(48)

(56)

CORRECT

INCORRECT

Summary of Contents for 697.68619 B1





































Search results

Summary of Contents for 697.68619 B1

Reviews:

Related manuals for 697.68619 B1

Brands by name

Popular brands

Arrow 697.68619 B1, Owner'S Manual & Assembly Instructions

Search results

Summary of Contents for 697.68619 B1

Reviews:

Related manuals for 697.68619 B1

Brands by name

Popular brands